Sika

Sika AnchorFix-3001

Two-part acrylic anchoring adhesive · US · manufacturer-sourced

Check your container: This countdown is for the Two-part acrylic anchoring adhesive variant. Similar-looking versions may have different times.

How long before Sika AnchorFix-3001 can take a load?

Short answer

Can take load or strain: 7 hours after application.
Adhesive & glue

Bond-strength path

Hold, handle and full load come at different times

  1. Join the parts with the Two-part acrylic anchoring adhesive
  2. Hold or clamp for the set time
  3. Put load on the bond only at full strength

This product’s stated stages Quoted at 73°F

  • Working time ends11 minutes
  • Ready for load7 hours

Worth noticing: Working time is only 11 minutes; the next stated stage, ready for load, is 7 hours.

Common mistake: Releasing the clamps because the glue line feels firm, long before it can carry a load.

Adhesive & glue

Bond-strength path

Assembly, handling and full load are different stages

1 · AssembleClean, fit and apply the Two-part acrylic anchoring adhesive version correctly.
2 · HoldKeep the joint undisturbed through its set or clamp stage.
3 · LoadUse full cure—not surface firmness—before demanding use.

Time bond readiness

When was the bond assembled?
Conditions that affect drying
Where?
Thickness

Stated times

  • Working time ends11 minutes
  • Can take load or strain7 hours

From Sika data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.

Manufacturer website: usa.sika.com

Conditions & fine print
  • Stated conditions: 73°F (23°C)
  • Gel and cure times depend on the temperature of the base material and the cartridge. Follow the current data sheet and the engineering instructions for your anchor.
  • Temperature range: 40°F to 104°F
  • Region US. Formulas can differ between countries; check your container.
  • Working time ends: Cartridge temperature of 72 to 77°F.
  • Can take load or strain: Base material temperature of 72 to 77°F.
  • Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
  • Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.

Confirm this is your product

Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.

Exact listing
Sika Sika AnchorFix-3001
Variant
Two-part acrylic anchoring adhesive
Region
US
Listed use
anchoring adhesive, threaded rod, rebar doweling
Timed stages recorded
tooling, load ready
Source checked
2026-10-25

Documentation: Technical data sheet · Edition 4.23.2021

Condition attached to the stated time: Cartridge temperature of 72 to 77°F.

About this product

A fast two-part anchoring adhesive for rods and dowels in concrete. Its work and load times come from a table indexed by cartridge and base-material temperature, from 24 hours to load in 40 to 49°F base material to 3 hours at 104°F.

Using this specific product

Sika Sika AnchorFix-3001 is listed here as the Two-part acrylic anchoring adhesive version for anchoring adhesive, threaded rod, and rebar doweling. For bonding parts, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.

Before you start

  • Confirm the package says Two-part acrylic anchoring adhesive; related versions can use different timing.
  • For anchoring adhesive, threaded rod, and rebar doweling, pay particular attention to surface fit, cleanliness, clamping pressure and bond-line thickness.
  • Cartridge temperature of 72 to 77°F. Base material temperature of 72 to 77°F.

How to check readiness

Test a noncritical offcut or wait for the stated load milestone before stressing the joint. The data sheet gives a work time of 11 minutes for a cartridge at 72 to 77°F. The data sheet gives 7 hours to load for a base material at 72 to 77°F.

Avoid this mistake

Handling strength and full load strength are different milestones.

Keep going

Questions

How long before this product can take a load?

Sika states: The data sheet gives a work time of 11 minutes for a cartridge at 72 to 77°F. Conditions: Cartridge temperature of 72 to 77°F.. The data sheet gives 7 hours to load for a base material at 72 to 77°F. Conditions: Base material temperature of 72 to 77°F.. These are the manufacturer’s stated times, not a guarantee.

How much does base material temperature change the load time for AnchorFix-3001?

A lot. The data sheet gives 24 hours at 40 to 49°F, 12 hours at 50 to 59°F, 8 hours at 59 to 72°F, 7 hours at 72 to 77°F, 6 hours at 77 to 86°F, 5 hours at 86 to 95°F, and 4 hours at 95 to 104°F. Work time falls from 20 minutes in a cold cartridge to 3 minutes at 104°F.

How long do I have to work with this product?

Sika states: The data sheet gives a work time of 11 minutes for a cartridge at 72 to 77°F. Conditions: Cartridge temperature of 72 to 77°F.. These are the manufacturer’s stated times, not a guarantee.

What affects how long this product takes to dry or cure?

Gel and cure times depend on the temperature of the base material and the cartridge. Follow the current data sheet and the engineering instructions for your anchor. Follow the product label for your conditions.

Similar products

All adhesives and glues