DAP Anchoring Adhesive
Two-part anchoring adhesive · US · manufacturer-sourced
How long before DAP Anchoring Adhesive can take a load?
Short answer
Bond-strength path
Hold, handle and full load come at different times
- Join the parts with the Two-part anchoring adhesive
- Hold or clamp for the set time
- Put load on the bond only at full strength
This product’s stated stages Quoted at 73°F
- Working time ends10 minutes
- Ready for load2 hours 25 min
Worth noticing: Working time is only 10 minutes; the next stated stage, ready for load, is 2 hours 25 min.
Common mistake: Releasing the clamps because the glue line feels firm, long before it can carry a load.
Bond-strength path
Assembly, handling and full load are different stages
Time bond readiness
Your countdown
Stated times
- Working time ends10 minutes
- Can take load or strain145 minutes
From DAP data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.
Manufacturer website: dap.com
Conditions & fine print
- Stated conditions: 73°F (23°C)
- Working and load times depend on both cartridge and base-material temperature. Follow the data sheet and the anchor engineering instructions.
- Region US. Formulas can differ between countries; check your container.
- Working time ends: Working time falls to 2.5 minutes for a cartridge at 104 to 113°F and rises to 30 minutes at 50°F.
- Can take load or strain: The sheet gives 5 hours below 68°F and 12 minutes at 113°F.
- Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
- Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.
Confirm this is your product
Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.
- Exact listing
- DAP DAP Anchoring Adhesive
- Variant
- Two-part anchoring adhesive
- Region
- US
- Listed use
- anchor bolts, threaded rod, concrete anchoring
- Timed stages recorded
- tooling, load ready
- Source checked
- 2026-10-25
Documentation: Technical data sheet · TDS dated 3/28/2023
Condition attached to the stated time: Working time falls to 2.5 minutes for a cartridge at 104 to 113°F and rises to 30 minutes at 50°F.
About this product
An anchoring adhesive whose sheet gives two temperature tables, one for the cartridge and one for the base material. At room temperature, working time is 10 minutes and full load takes 145 minutes, but at 113°F the load time drops to 12 minutes and the working time to 2.5.
Using this specific product
DAP DAP Anchoring Adhesive is listed here as the Two-part anchoring adhesive version for anchor bolts, threaded rod, and concrete anchoring. For bonding parts, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.
Before you start
- Confirm the package says Two-part anchoring adhesive; related versions can use different timing.
- For anchor bolts, threaded rod, and concrete anchoring, pay particular attention to surface fit, cleanliness, clamping pressure and bond-line thickness.
- Working time falls to 2.5 minutes for a cartridge at 104 to 113°F and rises to 30 minutes at 50°F. The sheet gives 5 hours below 68°F and 12 minutes at 113°F.
How to check readiness
Test a noncritical offcut or wait for the stated load milestone before stressing the joint. The data sheet gives a working time of 10 minutes for a cartridge at 68 to 77°F. The data sheet gives 145 minutes to full load capacity for base material at 68 to 77°F.
Avoid this mistake
Handling strength and full load strength are different milestones.
Questions
How long before this product can take a load?
DAP states: The data sheet gives a working time of 10 minutes for a cartridge at 68 to 77°F. Conditions: Working time falls to 2.5 minutes for a cartridge at 104 to 113°F and rises to 30 minutes at 50°F.. The data sheet gives 145 minutes to full load capacity for base material at 68 to 77°F. Conditions: The sheet gives 5 hours below 68°F and 12 minutes at 113°F.. These are the manufacturer’s stated times, not a guarantee.
How much does temperature change DAP Anchoring Adhesive's load time?
The data sheet gives 5 hours for base material at 68°F or below, 145 minutes at 68 to 77°F, 85 minutes at 77 to 86°F, 50 minutes at 86 to 95°F, 40 minutes at 95 to 104°F, 35 minutes at 104 to 113°F and 12 minutes at 113°F.
How long do I have to work with this product?
DAP states: The data sheet gives a working time of 10 minutes for a cartridge at 68 to 77°F. Conditions: Working time falls to 2.5 minutes for a cartridge at 104 to 113°F and rises to 30 minutes at 50°F.. These are the manufacturer’s stated times, not a guarantee.
What affects how long this product takes to dry or cure?
Working and load times depend on both cartridge and base-material temperature. Follow the data sheet and the anchor engineering instructions. Follow the product label for your conditions.