Tnemec

Series 161 Tneme-Fascure

Fast-curing epoxy, temperature-banded table · US · manufacturer-sourced

Check your container: This countdown is for the Fast-curing epoxy, temperature-banded table variant. Similar-looking versions may have different times.

How long before you can recoat Tnemec Series 161 Tneme-Fascure?

Short answer

Ready for another coat: 3–4 hours after application.
Safe to touch: 1 hour after application.
Industrial protective coatings

Film-build schedule

Recoat has a floor and a ceiling, and film thickness moves both

  1. Prepare the surface and apply the Fast-curing epoxy, temperature-banded table to the stated thickness
  2. Recoat inside the window the data sheet gives
  3. Return to service only at the stated cure

This product’s stated stages Quoted at 75°F

  • Safe to touch1 hour
  • Safe to handle2–3 hours
  • Ready for another coat3–4 hours
  • Immersion-ready3 days

Worth noticing: Safe to touch at 1 hour; immersion-ready at 3 days.

Common mistake: Recoating after the maximum window has closed; the next coat may not bond without abrading.

Industrial protective coatings

Coat timeline

Plan the next coat and final use separately

  1. 1
    ApplyUse the Fast-curing epoxy, temperature-banded table directions and prepare for steel coating and cold-weather coating.
  2. 2
    Next coatUse the listed recoat milestone; do not substitute touch-dry time.
  3. 3
    Normal useWait for the applicable handling, water or cure milestone.

Check the recoat window

When did this coat go on?
Conditions that affect drying
Where?
Thickness

Stated times

  • Safe to touch1 hour
  • Safe to handle2–3 hours
  • Ready for another coat3–4 hours
  • Immersion-ready3 days

From Tnemec product page · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.

Manufacturer website: tnemec.com

Conditions & fine print
  • Stated conditions: 75°F (24°C)
  • Protective-coating times are for the stated film thickness, temperature and humidity. Cold steel, thick films and poor airflow lengthen them. Follow the current data sheet.
  • Region US. Formulas can differ between countries; check your container.
  • Safe to touch: It is 2 hours at 65°F, 3 to 4 hours at 55°F and 8 to 10 hours at 35°F.
  • Safe to handle: It is 4 to 5 hours at 65°F and 16 to 18 hours at 35°F.
  • Ready for another coat: It is 5 to 6 hours at 65°F and 20 to 22 hours at 35°F.
  • Immersion-ready: It is 4 to 5 days at 65°F and 12 to 14 days at 35°F.
  • Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
  • Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.

Confirm this is your product

Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.

Exact listing
Tnemec Series 161 Tneme-Fascure
Variant
Fast-curing epoxy, temperature-banded table
Region
US
Listed use
steel coating, cold-weather coating
Timed stages recorded
touch, handle, recoat min, immersion
Source checked
2026-10-25

Documentation: Official product page · Product page, accessed 2026-10-26

Condition attached to the stated time: It is 2 hours at 65°F, 3 to 4 hours at 55°F and 8 to 10 hours at 35°F.

About this product

An epoxy built for cold work: the page runs a table down to 35°F, where touch dry takes 8 to 10 hours and immersion 12 to 14 days. At 75°F it is touch dry in an hour.

Using this specific product

Tnemec Series 161 Tneme-Fascure is listed here as the Fast-curing epoxy, temperature-banded table version for steel coating and cold-weather coating. For coating steel or industrial surfaces, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.

Before you start

  • Confirm the package says Fast-curing epoxy, temperature-banded table; related versions can use different timing.
  • For steel coating and cold-weather coating, pay particular attention to surface preparation, film thickness, temperature, dew point and pot life.
  • It is 2 hours at 65°F, 3 to 4 hours at 55°F and 8 to 10 hours at 35°F. It is 4 to 5 hours at 65°F and 16 to 18 hours at 35°F. It is 5 to 6 hours at 65°F and 20 to 22 hours at 35°F. It is 4 to 5 days at 65°F and 12 to 14 days at 35°F.

How to check readiness

Check dry film thickness and the recoat window before the next coat. Touch only a hidden edge first; a dry surface can conceal a soft layer underneath. Lift or move the item gently and avoid twisting the bond or pressing finished faces together. Before recoating, confirm the first coat matches the manufacturer’s stated condition; if the maximum window passed, check whether sanding is required.

Avoid this mistake

Recoat windows can close; past the maximum, abrading is usually required.

Compare with similar products

Keep going

Questions

How long before you can recoat this product?

Tnemec states: The page gives touch dry at 1 hour at 75°F. Conditions: It is 2 hours at 65°F, 3 to 4 hours at 55°F and 8 to 10 hours at 35°F.. The page gives handle at 2 to 3 hours at 75°F. Conditions: It is 4 to 5 hours at 65°F and 16 to 18 hours at 35°F.. The page gives recoating after 3 to 4 hours at 75°F. Conditions: It is 5 to 6 hours at 65°F and 20 to 22 hours at 35°F.. The page gives immersion after 3 days at 75°F. Conditions: It is 4 to 5 days at 65°F and 12 to 14 days at 35°F.. These are the manufacturer’s stated times, not a guarantee.

How slow is Tneme-Fascure at 35°F?

The page gives 8 to 10 hours to touch, 16 to 18 to handle, 20 to 22 to recoat and 12 to 14 days to immersion.

How long before this product can be immersed in water?

Tnemec states: The page gives immersion after 3 days at 75°F. Conditions: It is 4 to 5 days at 65°F and 12 to 14 days at 35°F.. These are the manufacturer’s stated times, not a guarantee.

How long until this product is safe to touch?

Tnemec states: The page gives touch dry at 1 hour at 75°F. Conditions: It is 2 hours at 65°F, 3 to 4 hours at 55°F and 8 to 10 hours at 35°F.. These are the manufacturer’s stated times, not a guarantee.

How long until this product is safe to handle?

Tnemec states: The page gives handle at 2 to 3 hours at 75°F. Conditions: It is 4 to 5 hours at 65°F and 16 to 18 hours at 35°F.. These are the manufacturer’s stated times, not a guarantee.

What affects how long this product takes to dry or cure?

Protective-coating times are for the stated film thickness, temperature and humidity. Cold steel, thick films and poor airflow lengthen them. Follow the current data sheet. Follow the product label for your conditions.

Similar products

All industrial protective coatings