Tnemec

Series 27 F.C. Typoxy

Epoxy with a long recoat window · US · manufacturer-sourced

Check your container: This countdown is for the Epoxy with a long recoat window variant. Similar-looking versions may have different times.

How long before you can recoat Tnemec Series 27 F.C. Typoxy?

Short answer

Ready for another coat: 3 hours after application.
Safe to touch: 30 minutes after application.
Industrial protective coatings

Film-build schedule

Recoat has a floor and a ceiling, and film thickness moves both

  1. Prepare the surface and apply the Epoxy with a long recoat window to the stated thickness
  2. Recoat inside the window the data sheet gives
  3. Return to service only at the stated cure

This product’s stated stages Quoted at 75°F

  • Safe to touch30 minutes
  • Ready for another coat3 hours
  • Recoat window closes2 weeks

Worth noticing: Recoat inside the window: not before 3 hours and not after 2 weeks.

Common mistake: Recoating after the maximum window has closed; the next coat may not bond without abrading.

Industrial protective coatings

Coat timeline

Plan the next coat and final use separately

  1. 1
    ApplyUse the Epoxy with a long recoat window directions and prepare for steel coating and recoating.
  2. 2
    Next coatUse the listed recoat milestone; do not substitute touch-dry time.
  3. 3
    Normal useWait for the applicable handling, water or cure milestone.

Check the recoat window

When did this coat go on?
Conditions that affect drying
Where?
Thickness

Stated times

  • Safe to touch30 minutes
  • Recoat window closes14 days
  • Ready for another coat3 hours

From Tnemec product page · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.

Manufacturer website: tnemec.com

Conditions & fine print
  • Stated conditions: 75°F (24°C)
  • Protective-coating times are for the stated film thickness, temperature and humidity. Cold steel, thick films and poor airflow lengthen them. Follow the current data sheet.
  • Region US. Formulas can differ between countries; check your container.
  • Safe to touch: It is 45 minutes at 65°F and 2 to 3 hours at 35°F.
  • Recoat window closes: Others allow 30 days.
  • Ready for another coat: It is 5 to 6 hours at 65°F and 12 to 15 hours at 35°F.
  • Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
  • Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.

Confirm this is your product

Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.

Exact listing
Tnemec Series 27 F.C. Typoxy
Variant
Epoxy with a long recoat window
Region
US
Listed use
steel coating, recoating
Timed stages recorded
touch, recoat max, recoat min
Source checked
2026-10-25

Documentation: Official product page · Product page, accessed 2026-10-26

Condition attached to the stated time: It is 45 minutes at 65°F and 2 to 3 hours at 35°F.

About this product

A fast-touching epoxy at 30 minutes, with recoat after 3 hours at 75°F and a window of 14 or 30 days depending on the topcoat chosen.

Using this specific product

Tnemec Series 27 F.C. Typoxy is listed here as the Epoxy with a long recoat window version for steel coating and recoating. For coating steel or industrial surfaces, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.

Before you start

  • Confirm the package says Epoxy with a long recoat window; related versions can use different timing.
  • For steel coating and recoating, pay particular attention to surface preparation, film thickness, temperature, dew point and pot life.
  • It is 45 minutes at 65°F and 2 to 3 hours at 35°F. Others allow 30 days. It is 5 to 6 hours at 65°F and 12 to 15 hours at 35°F.

How to check readiness

Check dry film thickness and the recoat window before the next coat. Touch only a hidden edge first; a dry surface can conceal a soft layer underneath. The page gives a 14 day maximum recoat for some topcoats. Before recoating, confirm the first coat matches the manufacturer’s stated condition; if the maximum window passed, check whether sanding is required.

Avoid this mistake

Recoat windows can close; past the maximum, abrading is usually required.

Compare with similar products

Keep going

Questions

How long before you can recoat this product?

Tnemec states: The page gives touch dry at 30 minutes at 75°F. Conditions: It is 45 minutes at 65°F and 2 to 3 hours at 35°F.. The page gives a 14 day maximum recoat for some topcoats. Conditions: Others allow 30 days.. The page gives recoating after 3 hours at 75°F. Conditions: It is 5 to 6 hours at 65°F and 12 to 15 hours at 35°F.. These are the manufacturer’s stated times, not a guarantee.

How long can Series 27 wait before topcoating?

The page gives 14 days for some topcoats and 30 days for others.

How long until this product is safe to touch?

Tnemec states: The page gives touch dry at 30 minutes at 75°F. Conditions: It is 45 minutes at 65°F and 2 to 3 hours at 35°F.. These are the manufacturer’s stated times, not a guarantee.

What affects how long this product takes to dry or cure?

Protective-coating times are for the stated film thickness, temperature and humidity. Cold steel, thick films and poor airflow lengthen them. Follow the current data sheet. Follow the product label for your conditions.

Similar products

All industrial protective coatings