Hempel

Hempaprime Multi 500

General-purpose epoxy primer · INTL · manufacturer-sourced

Check your container: This countdown is for the General-purpose epoxy primer variant. Similar-looking versions may have different times.

How long before you can recoat Hempel Hempaprime Multi 500?

Short answer

Ready for another coat: 3 hours after application.
Safe to touch: 1 hour after application.
Industrial protective coatings

Film-build schedule

Recoat has a floor and a ceiling, and film thickness moves both

  1. Prepare the surface and apply the General-purpose epoxy primer to the stated thickness
  2. Recoat inside the window the data sheet gives
  3. Return to service only at the stated cure

This product’s stated stages Quoted at 68°F

  • Working time ends1 hour
  • Safe to touch1 hour
  • Ready for another coat3 hours
  • Full cure7 days

Worth noticing: Touch-dry comes at 1 hour, but full cure is 7 days, about 168 times longer.

Common mistake: Recoating after the maximum window has closed; the next coat may not bond without abrading.

Industrial protective coatings

Coat timeline

Plan the next coat and final use separately

  1. 1
    ApplyUse the General-purpose epoxy primer directions and prepare for steel priming.
  2. 2
    Next coatUse the listed recoat milestone; do not substitute touch-dry time.
  3. 3
    Normal useWait for the applicable handling, water or cure milestone.

Check the recoat window

When did this coat go on?
Conditions that affect drying
Where?
Thickness

Stated times

  • Working time ends1 hour
  • Safe to touch1 hour
  • Ready for another coat3 hours
  • Full cure7 days

From Hempel data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.

Manufacturer website: hempel.com

Conditions & fine print
  • Stated conditions: 68°F (20°C)
  • Pot life and cure times shorten in warm rooms and with larger batches. Follow the current data sheet and mixing instructions.
  • Temperature range: 50°F to 104°F
  • Region INTL. Formulas can differ between countries; check your container.
  • Working time ends: 2.5 hours at 10°C, 45 minutes at 30°C and 30 minutes at 40°C.
  • Safe to touch: The sheet gives touch dry the same as pot life across the range.
  • Ready for another coat: 7 hours at 10°C, 2 hours at 30°C and 1.5 hours at 40°C.
  • Full cure: The source gives no conditions for this time.
  • Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
  • Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.

Confirm this is your product

Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.

Exact listing
Hempel Hempaprime Multi 500
Variant
General-purpose epoxy primer
Region
INTL
Listed use
steel priming
Timed stages recorded
tooling, touch, recoat min, full cure
Source checked
2026-10-25

Documentation: Technical data sheet · Product data sheet, October 2026

Condition attached to the stated time: 2.5 hours at 10°C, 45 minutes at 30°C and 30 minutes at 40°C.

About this product

A general epoxy primer with a four-temperature table: overcoat from 7 hours at 10°C down to 1.5 hours at 40°C, and cure in 7 days at 20°C.

Using this specific product

Hempel Hempaprime Multi 500 is listed here as the General-purpose epoxy primer version for steel priming. For coating steel or industrial surfaces, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.

Before you start

  • Confirm the package says General-purpose epoxy primer; related versions can use different timing.
  • For steel priming, pay particular attention to surface preparation, film thickness, temperature, dew point and pot life.
  • 2.5 hours at 10°C, 45 minutes at 30°C and 30 minutes at 40°C. The sheet gives touch dry the same as pot life across the range. 7 hours at 10°C, 2 hours at 30°C and 1.5 hours at 40°C. The source gives no conditions for this time.

How to check readiness

Check dry film thickness and the recoat window before the next coat. The sheet gives a pot life of 1 hour at 20°C. Touch only a hidden edge first; a dry surface can conceal a soft layer underneath. Before recoating, confirm the first coat matches the manufacturer’s stated condition; if the maximum window passed, check whether sanding is required.

Avoid this mistake

Recoat windows can close; past the maximum, abrading is usually required.

Compare with similar products

Keep going

Questions

How long before you can recoat this product?

Hempel states: The sheet gives a pot life of 1 hour at 20°C. Conditions: 2.5 hours at 10°C, 45 minutes at 30°C and 30 minutes at 40°C.. The sheet gives touch dry at 1 hour at 20°C. Conditions: The sheet gives touch dry the same as pot life across the range.. The sheet gives a minimum overcoat of 3 hours at 20°C. Conditions: 7 hours at 10°C, 2 hours at 30°C and 1.5 hours at 40°C.. The sheet gives cure at 7 days at 20°C. Conditions: The source gives no conditions for this time.. These are the manufacturer’s stated times, not a guarantee.

What is the minimum overcoat time for Hempaprime Multi 500 at 20°C?

The sheet gives 3 hours.

How long does this product take to fully cure?

Hempel states: The sheet gives cure at 7 days at 20°C. Conditions: The source gives no conditions for this time.. These are the manufacturer’s stated times, not a guarantee.

How long do I have to work with this product?

Hempel states: The sheet gives a pot life of 1 hour at 20°C. Conditions: 2.5 hours at 10°C, 45 minutes at 30°C and 30 minutes at 40°C.. These are the manufacturer’s stated times, not a guarantee.

How long until this product is safe to touch?

Hempel states: The sheet gives touch dry at 1 hour at 20°C. Conditions: The sheet gives touch dry the same as pot life across the range.. These are the manufacturer’s stated times, not a guarantee.

What affects how long this product takes to dry or cure?

Pot life and cure times shorten in warm rooms and with larger batches. Follow the current data sheet and mixing instructions. Follow the product label for your conditions.

Similar products

All industrial protective coatings