Super Gloss Enamel
Solvent-borne gloss enamel (D32) · NZ · manufacturer-sourced
How long before you can recoat Resene Super Gloss Enamel?
Short answer
Coat-by-coat plan
Touch-dry, recoat and washable are three different dates
- Cut in and roll the Solvent-borne gloss enamel (D32) in even coats
- Wait for the recoat time, not touch-dry
- Hold off scrubbing until the cure time
This product’s stated stages Quoted at 64°F
- Fully dry4 hours
- Ready for another coat16 hours
Worth noticing: Fully dry at 4 hours; ready for another coat at 16 hours.
Common mistake: Closing the door or hanging pictures once the wall feels dry, long before the film has hardened.
Coat timeline
Plan the next coat and final use separately
- 1ApplyUse the Solvent-borne gloss enamel (D32) directions and prepare for trim, doors, and furniture.
- 2Next coatUse the listed recoat milestone; do not substitute touch-dry time.
- 3Normal useWait for the applicable handling, water or cure milestone.
Plan the next coat
Your countdown
Stated times
- Ready for another coat16 hours
- Fully dry4 hours
From Resene data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.
Manufacturer website: resene.co.nz
Conditions & fine print
- Stated conditions: 64°F (18°C)
- Dry and recoat times change with temperature, humidity and film build. Follow the current data sheet and label.
- Region NZ. Formulas can differ between countries; check your container.
- Ready for another coat: The sheet gives no temperature for this figure.
- Fully dry: At 18°C.
- Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
- Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.
Confirm this is your product
Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.
- Exact listing
- Resene Super Gloss Enamel
- Variant
- Solvent-borne gloss enamel (D32)
- Region
- NZ
- Listed use
- trim, doors, furniture
- Timed stages recorded
- recoat min, full dry
- Source checked
- 2026-10-25
Documentation: Technical data sheet · Data sheet D32, Dec 2014
Condition attached to the stated time: The sheet gives no temperature for this figure.
About this product
A solvent-borne gloss enamel with a long recoat wait: 16 hours between coats, against 4 hours to dry. Sanding between coats is the usual way to bridge the gap.
Using this specific product
Resene Super Gloss Enamel is listed here as the Solvent-borne gloss enamel (D32) version for trim, doors, and furniture. For painting, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.
Before you start
- Confirm the package says Solvent-borne gloss enamel (D32); related versions can use different timing.
- For trim, doors, and furniture, pay particular attention to surface preparation, coat thickness and ventilation.
- The sheet gives no temperature for this figure. At 18°C.
How to check readiness
Test an inconspicuous area for firmness and blocking before normal use. Before recoating, confirm the first coat matches the manufacturer’s stated condition; if the maximum window passed, check whether sanding is required. The sheet gives a minimum dry time of 4 hours at 18°C.
Avoid this mistake
Recoating too early can trap solvent or water; waiting much longer may require scuffing under the label directions.
Compare with similar products
- Compare with Little Greene Traditional Oil GlossRecoat: 16 h there, 16 h here.
- Compare with Ames Maximum-StretchRecoat: 1 day there, 16 h here.
Questions
How long before you can recoat this product?
Resene states: The sheet gives a minimum recoat time of 16 hours. Conditions: The sheet gives no temperature for this figure.. The sheet gives a minimum dry time of 4 hours at 18°C. Conditions: At 18°C.. These are the manufacturer’s stated times, not a guarantee.
How long between coats of Resene Super Gloss?
The sheet gives a minimum of 16 hours.
How long until this product is fully dry?
Resene states: The sheet gives a minimum dry time of 4 hours at 18°C. Conditions: At 18°C.. These are the manufacturer’s stated times, not a guarantee.
What affects how long this product takes to dry or cure?
Dry and recoat times change with temperature, humidity and film build. Follow the current data sheet and label. Follow the product label for your conditions.