Table Top Pro
Table and bar top epoxy · US · manufacturer-sourced
How long before you can recoat MAS Epoxies Table Top Pro?
Short answer
Two-part cure ladder
Pot life, set and full cure all run off the mix time
- Mix the Table and bar top epoxy in the exact ratio
- Work inside the pot life
- Do not load until the stated cure
This product’s stated stages
- Working time ends30 minutes
- Ready for another coat4–8 hours
Worth noticing: Working time is only 30 minutes; the next stated stage, ready for another coat, is 4–8 hours.
Common mistake: Mixing a large batch in a warm room; the pot life is shorter than the sheet suggests.
Bond-strength path
Assembly, handling and full load are different stages
Time the epoxy cure
Your countdown
Stated times
- Working time ends30 minutes
- Ready for another coat4–8 hours
From MAS Epoxies data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.
Manufacturer website: masepoxies.com
Conditions & fine print
- Stated conditions: Not stated in the data sheet
- Pot life and cure time shorten in heat, with larger mixed batches and in thick sections. Follow the current data sheet for mixing, surface preparation and loading. The bulletin says to use it at 70 to 80°F and gives no full cure time.
- Temperature range: 70°F to 80°F
- Region US. Formulas can differ between countries; check your container.
- Working time ends: At 77°F (25°C).
- Ready for another coat: The source gives no conditions for this time.
- Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
- Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.
Confirm this is your product
Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.
- Exact listing
- MAS Epoxies Table Top Pro
- Variant
- Table and bar top epoxy
- Region
- US
- Listed use
- tabletop epoxy, bar top, clear coat
- Timed stages recorded
- tooling, recoat min
- Source checked
- 2026-10-25
Documentation: Technical data sheet · Revised December 2019
Condition attached to the stated time: At 77°F (25°C).
About this product
A clear flood-coat epoxy for tables and bar tops. The bulletin is short on cure times: it gives the 30 minute gel time and a 4 to 8 hour recoat window, but no full cure figure.
Using this specific product
MAS Epoxies Table Top Pro is listed here as the Table and bar top epoxy version for tabletop epoxy, bar top, and clear coat. For mixing and curing epoxy, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.
Before you start
- Confirm the package says Table and bar top epoxy; related versions can use different timing.
- For tabletop epoxy, bar top, and clear coat, pay particular attention to mix ratio, batch size, temperature and pour thickness.
- At 77°F (25°C). The source gives no conditions for this time.
How to check readiness
Check the coolest or thickest part for firmness before sanding, demolding or loading. The bulletin gives a gel time of 30 minutes for a 150 gram mass. Before recoating, confirm the first coat matches the manufacturer’s stated condition; if the maximum window passed, check whether sanding is required.
Avoid this mistake
A larger batch can heat faster while a thin film may cure more slowly.
Compare with similar products
- Compare with Dulux Protective Coatings Luxafloor RollCoatRecoat: 6 h there, 4–8 h here.
- Compare with Dulux Protective Coatings Luxafloor Express FCFRecoat: 2 h there, 4–8 h here.
Questions
How long before you can recoat this product?
MAS Epoxies states: The bulletin gives a gel time of 30 minutes for a 150 gram mass. Conditions: At 77°F (25°C).. The bulletin says the epoxy can usually be recoated in 4 to 8 hours without sanding. Conditions: The source gives no conditions for this time.. These are the manufacturer’s stated times, not a guarantee.
Do I have to sand Table Top Pro between coats?
Not if you recoat inside the window. The bulletin says the epoxy can usually be recoated in 4 to 8 hours without any additional prep work or sanding.
How long do I have to work with this product?
MAS Epoxies states: The bulletin gives a gel time of 30 minutes for a 150 gram mass. Conditions: At 77°F (25°C).. These are the manufacturer’s stated times, not a guarantee.
What affects how long this product takes to dry or cure?
Pot life and cure time shorten in heat, with larger mixed batches and in thick sections. Follow the current data sheet for mixing, surface preparation and loading. The bulletin says to use it at 70 to 80°F and gives no full cure time. Follow the product label for your conditions.