Dulux Protective Coatings

Luxafloor RollCoat

Roll-applied epoxy floor coating · AU · manufacturer-sourced

Check your container: This countdown is for the Roll-applied epoxy floor coating variant. Similar-looking versions may have different times.

How long before you can recoat Dulux Protective Coatings Luxafloor RollCoat?

Short answer

Ready for another coat: 6 hours after application.
Safe to touch: 2 hours after application.
Epoxy

Two-part cure ladder

Pot life, set and full cure all run off the mix time

  1. Mix the Roll-applied epoxy floor coating in the exact ratio
  2. Work inside the pot life
  3. Do not load until the stated cure

This product’s stated stages Quoted at 77°F and 50% humidity

  • Working time ends1 hour
  • Safe to touch2 hours
  • Ready for another coat6 hours
  • Light use16 hours
  • Recoat window closes18 hours
  • Full cure7 days

Worth noticing: Recoat inside the window: not before 6 hours and not after 18 hours.

Common mistake: Mixing a large batch in a warm room; the pot life is shorter than the sheet suggests.

Epoxy

Bond-strength path

Assembly, handling and full load are different stages

1 · AssembleClean, fit and apply the Roll-applied epoxy floor coating version correctly.
2 · HoldKeep the joint undisturbed through its set or clamp stage.
3 · LoadUse full cure—not surface firmness—before demanding use.

Time the epoxy cure

When did you mix the epoxy?
Conditions that affect drying
Where?
Thickness

Stated times

  • Working time ends1 hour
  • Safe to touch2 hours
  • Recoat window closes18 hours
  • Ready for another coat6 hours
  • Light use16 hours
  • Full cure7 days

From Dulux Protective Coatings data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.

Manufacturer website: duluxprotectivecoatings.com.au

Conditions & fine print
  • Stated conditions: 77°F (25°C) and 50% relative humidity
  • Floor times assume the stated temperature and humidity. Cold slabs, thick coats and damp subfloors lengthen them. Follow the current data sheet.
  • Temperature range: 59°F to 77°F
  • Region AU. Formulas can differ between countries; check your container.
  • Working time ends: At 77°F (25°C) and 50% relative humidity.
  • Safe to touch: 4 hours at 15°C.
  • Recoat window closes: The source gives no conditions for this time.
  • Ready for another coat: The source gives no conditions for this time.
  • Light use: The source gives no conditions for this time.
  • Full cure: The source gives no conditions for this time.
  • Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
  • Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.

Confirm this is your product

Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.

Exact listing
Dulux Protective Coatings Luxafloor RollCoat
Variant
Roll-applied epoxy floor coating
Region
AU
Listed use
garage floors, warehouses
Timed stages recorded
tooling, touch, recoat max, recoat min, light use
Source checked
2026-10-25

Documentation: Technical data sheet · Product data sheet PC 227, August 2018

Condition attached to the stated time: At 77°F (25°C) and 50% relative humidity.

About this product

A roll-on floor epoxy with an overcoat window from 6 to 18 hours at 25°C, light traffic at 16 hours and full cure at 7 days.

Using this specific product

Dulux Protective Coatings Luxafloor RollCoat is listed here as the Roll-applied epoxy floor coating version for garage floors and warehouses. For mixing and curing epoxy, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.

Before you start

  • Confirm the package says Roll-applied epoxy floor coating; related versions can use different timing.
  • For garage floors and warehouses, pay particular attention to mix ratio, batch size, temperature and pour thickness.
  • At 77°F (25°C) and 50% relative humidity. 4 hours at 15°C. The source gives no conditions for this time.

How to check readiness

Check the coolest or thickest part for firmness before sanding, demolding or loading. The sheet gives a standard pot life of 60 minutes. Touch only a hidden edge first; a dry surface can conceal a soft layer underneath. The sheet gives a maximum overcoat of 18 hours at 25°C.

Avoid this mistake

A larger batch can heat faster while a thin film may cure more slowly.

Compare with similar products

Keep going

Questions

How long before you can recoat this product?

Dulux Protective Coatings states: The sheet gives a standard pot life of 60 minutes. Conditions: At 77°F (25°C) and 50% relative humidity.. The sheet gives touch dry at 2 hours at 25°C. Conditions: 4 hours at 15°C.. The sheet gives a maximum overcoat of 18 hours at 25°C. Conditions: The source gives no conditions for this time.. The sheet gives a minimum overcoat of 6 hours at 25°C. Conditions: The source gives no conditions for this time.. The sheet gives light traffic at 16 hours at 25°C. Conditions: The source gives no conditions for this time.. The sheet gives full cure at 7 days. Conditions: The source gives no conditions for this time.. These are the manufacturer’s stated times, not a guarantee.

How long is the Luxafloor RollCoat overcoat window?

At 25°C it runs from 6 to 18 hours.

How long does this product take to fully cure?

Dulux Protective Coatings states: The sheet gives full cure at 7 days. Conditions: The source gives no conditions for this time.. These are the manufacturer’s stated times, not a guarantee.

How long do I have to work with this product?

Dulux Protective Coatings states: The sheet gives a standard pot life of 60 minutes. Conditions: At 77°F (25°C) and 50% relative humidity.. These are the manufacturer’s stated times, not a guarantee.

How long until this product is safe to touch?

Dulux Protective Coatings states: The sheet gives touch dry at 2 hours at 25°C. Conditions: 4 hours at 15°C.. These are the manufacturer’s stated times, not a guarantee.

What affects how long this product takes to dry or cure?

Floor times assume the stated temperature and humidity. Cold slabs, thick coats and damp subfloors lengthen them. Follow the current data sheet. Follow the product label for your conditions.

Similar products

All epoxies