Thixo Fast Cure
Thickened epoxy adhesive · US · manufacturer-sourced
How long should TotalBoat Thixo Fast Cure stay clamped?
Short answer
Two-part cure ladder
Pot life, set and full cure all run off the mix time
- Mix the Thickened epoxy adhesive in the exact ratio
- Work inside the pot life
- Do not load until the stated cure
This product’s stated stages
- Working time ends30 minutes
- Clamps off1 day
Worth noticing: Working time is only 30 minutes; the next stated stage, clamps off, is 1 day.
Common mistake: Mixing a large batch in a warm room; the pot life is shorter than the sheet suggests.
Bond-strength path
Assembly, handling and full load are different stages
Time the epoxy cure
Your countdown
Stated times
- Working time ends30 minutes
- Clamps can come off1 day
From TotalBoat data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.
Manufacturer website: totalboat.com
Conditions & fine print
- Stated conditions: Not stated in the data sheet
- Pot life and cure time shorten in heat, with larger mixed batches and in thick sections. Follow the current data sheet for mixing, surface preparation and loading. The sheet's handling table lists a 10 minute gel time for a 150 gram mass, which is shorter than the 30 minute text figure. It recommends use at 55°F or higher.
- Apply at 55°F or above
- Region US. Formulas can differ between countries; check your container.
- Working time ends: At 77°F (25°C).
- Clamps can come off: The source gives no conditions for this time.
- Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
- Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.
Confirm this is your product
Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.
- Exact listing
- TotalBoat Thixo Fast Cure
- Variant
- Thickened epoxy adhesive
- Region
- US
- Listed use
- gap filling epoxy, wood bonding, boat building
- Timed stages recorded
- tooling, clamp
- Source checked
- 2026-10-25
Documentation: Technical data sheet · Revised December 2014
Condition attached to the stated time: At 77°F (25°C).
About this product
A thickened (non-sag) epoxy adhesive from TotalBoat for bonding and gap filling. Its data sheet gives two gel figures, 30 minutes in the text and 10 minutes in the 150 gram table, so check your batch size.
Using this specific product
TotalBoat Thixo Fast Cure is listed here as the Thickened epoxy adhesive version for gap filling epoxy, wood bonding, and boat building. For mixing and curing epoxy, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.
Before you start
- Confirm the package says Thickened epoxy adhesive; related versions can use different timing.
- For gap filling epoxy, wood bonding, and boat building, pay particular attention to mix ratio, batch size, temperature and pour thickness.
- At 77°F (25°C). The source gives no conditions for this time.
How to check readiness
Check the coolest or thickest part for firmness before sanding, demolding or loading. The data sheet says the adhesive will gel in about 30 minutes. Remove pressure gradually and avoid loading the joint until its later strength milestone.
Avoid this mistake
A larger batch can heat faster while a thin film may cure more slowly.
Questions
How long should this product stay clamped?
TotalBoat states: The data sheet says the adhesive will gel in about 30 minutes. Conditions: At 77°F (25°C).. The data sheet says to keep parts clamped until the adhesive is cured, about 24 hours. Conditions: The source gives no conditions for this time.. These are the manufacturer’s stated times, not a guarantee.
Why does the Thixo Fast Cure sheet show two gel times?
The text says the adhesive gels in about 30 minutes at 77°F. The handling table lists a gel time of 10 minutes at 77°F for a 150 gram mass. The sheet does not explain the gap; a larger, hotter mass gels faster, so plan on the shorter figure for big batches.
How long do I have to work with this product?
TotalBoat states: The data sheet says the adhesive will gel in about 30 minutes. Conditions: At 77°F (25°C).. These are the manufacturer’s stated times, not a guarantee.
What affects how long this product takes to dry or cure?
Pot life and cure time shorten in heat, with larger mixed batches and in thick sections. Follow the current data sheet for mixing, surface preparation and loading. The sheet's handling table lists a 10 minute gel time for a 150 gram mass, which is shorter than the 30 minute text figure. It recommends use at 55°F or higher. Follow the product label for your conditions.