Smooth-On

TASK 2

Urethane casting resin · US · manufacturer-sourced

Check your container: This countdown is for the Urethane casting resin variant. Similar-looking versions may have different times.

How long before you can demold Smooth-On TASK 2?

Short answer

Ready to demold: 1 hour after application.
Maker & casting resin

Cast-and-demold plan

Gel, demold and full cure are separate days

  1. Mix the Urethane casting resin to ratio and pour
  2. Wait for the demold time
  3. Sand or finish after full cure

This product’s stated stages

  • Working time ends7 minutes
  • Demold1 hour

Worth noticing: Working time is only 7 minutes; the next stated stage, demold, is 1 hour.

Common mistake: Demolding early and leaving a soft, tacky casting that never fully hardens.

Maker & casting resin

Project stage ladder

Demolding, handling, finishing and final use may occur at different times

ShapeSetFinishUse

For casting and prototyping, identify which stage the stated to demold 1 hour milestone actually unlocks. Earlier handling does not prove final cure.

Time demold and cure

When did you mix and pour?
Conditions that affect drying
Where?
Thickness

Stated times

  • Working time ends7 minutes
  • Ready to demold1 hour

From Smooth-On data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.

Manufacturer website: smooth-on.com

Conditions & fine print
  • Stated conditions: Not stated in the data sheet
  • Pot life and cure time shorten in warm rooms and with bigger batches. Follow the current technical bulletin for mix ratio, mixing and release agents. The chart is a summary; read the product's technical bulletin before you pour.
  • Region US. Formulas can differ between countries; check your container.
  • Working time ends: The chart gives no temperature.
  • Ready to demold: The chart gives no temperature; its cure column is the last time value in each row.
  • Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
  • Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.

Confirm this is your product

Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.

Exact listing
Smooth-On TASK 2
Variant
Urethane casting resin
Region
US
Listed use
casting, prototyping
Timed stages recorded
tooling, demold
Source checked
2026-10-25

Documentation: Technical data sheet · Technical Data Chart (no revision date)

Condition attached to the stated time: The chart gives no temperature.

About this product

TASK 2 is a urethane casting resin (TASK) on Smooth-On's technical data chart, listed with a pot life of 7 minutes and a cure time of 60 minutes. Its pot life is number 6 of 14 from shortest to longest in that comparison. This page uses only the chart values; mix ratio, hardness and release details come from Smooth-On's product bulletin.

Using this specific product

Smooth-On TASK 2 is listed here as the Urethane casting resin version for casting and prototyping. For casting resin, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.

Before you start

  • Confirm the package says Urethane casting resin; related versions can use different timing.
  • For casting and prototyping, pay particular attention to accurate mixing, mold material, mass and room temperature.
  • The chart gives no temperature. The chart gives no temperature; its cure column is the last time value in each row.

How to check readiness

Check the casting itself for flex or tack before demolding. The technical data chart gives a pot life of 7 minutes. Flex the mold away at one edge and stop if the casting bends, tears or remains tacky.

Avoid this mistake

Demold time is not necessarily full mechanical cure.

Compare with similar products

Keep going

Questions

How long before you can demold this product?

Smooth-On states: The technical data chart gives a pot life of 7 minutes. Conditions: The chart gives no temperature.. The technical data chart gives a cure time of 60 minutes. Conditions: The chart gives no temperature; its cure column is the last time value in each row.. These are the manufacturer’s stated times, not a guarantee.

How does TASK 2 compare with others in its line on the chart?

On Smooth-On's technical data chart, TASK 2 lists a pot life of 7 minutes and a cure time of 60 minutes. Among the 14 TASK rows in this comparison the shortest pot life is TASK 5 (3 minutes) and the longest is TASK 3 (20 minutes); cure times run from TASK 13 (20 minutes) to TASK 5 (24 hours). The chart shows the same pot life and cure time for TASK 9, so those lines are told apart by hardness and handling, not by timing.

How long after the pot life ends does TASK 2 take to cure?

The chart gives a pot life of 7 minutes and a cure time of 60 minutes. If the cure clock starts at mixing, that is about 53 minutes after the pot life ends. The chart does not state a temperature for these values, so treat that gap as a planning number, not a promise.

How long do I have to work with this product?

Smooth-On states: The technical data chart gives a pot life of 7 minutes. Conditions: The chart gives no temperature.. These are the manufacturer’s stated times, not a guarantee.

What affects how long this product takes to dry or cure?

Pot life and cure time shorten in warm rooms and with bigger batches. Follow the current technical bulletin for mix ratio, mixing and release agents. The chart is a summary; read the product's technical bulletin before you pour. Follow the product label for your conditions.