Ecoflex 00-20
Platinum silicone · US · manufacturer-sourced
How long before you can demold Smooth-On Ecoflex 00-20?
Short answer
Cast-and-demold plan
Gel, demold and full cure are separate days
- Mix the Platinum silicone to ratio and pour
- Wait for the demold time
- Sand or finish after full cure
This product’s stated stages Quoted at 73°F
- Working time ends30 minutes
- Demold4 hours
Worth noticing: Working time is only 30 minutes; the next stated stage, demold, is 4 hours.
Common mistake: Demolding early and leaving a soft, tacky casting that never fully hardens.
Project stage ladder
Demolding, handling, finishing and final use may occur at different times
For prosthetics, soft silicone, and special effects, identify which stage the stated to demold 4 hours milestone actually unlocks. Earlier handling does not prove final cure.
Time demold and cure
Your countdown
Stated times
- Working time ends30 minutes
- Ready to demold4 hours
From Smooth-On data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.
Manufacturer website: smooth-on.com
Conditions & fine print
- Stated conditions: 73°F (23°C)
- Pot life and cure time shorten in warm rooms and with bigger batches. Follow the current technical bulletin for mix ratio, mixing and release agents.
- Region US. Formulas can differ between countries; check your container.
- Working time ends: At 73°F (23°C).
- Ready to demold: At 73°F (23°C).
- Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
- Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.
Confirm this is your product
Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.
- Exact listing
- Smooth-On Ecoflex 00-20
- Variant
- Platinum silicone
- Region
- US
- Listed use
- prosthetics, soft silicone, special effects
- Timed stages recorded
- tooling, demold
- Source checked
- 2026-10-25
Documentation: Technical data sheet · TB code 011124DH
Condition attached to the stated time: At 73°F (23°C).
About this product
Ecoflex 00-20 is a maker & casting resin product from Smooth-On, listed for prosthetics, soft silicone, special effects. Its times are stated under: At 73°F (23°C). Its demold time of 4 hours is shorter than 53% of the 95 maker & casting resin products here that list one.
Using this specific product
Smooth-On Ecoflex 00-20 is listed here as the Platinum silicone version for prosthetics, soft silicone, and special effects. For casting resin, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.
Before you start
- Confirm the package says Platinum silicone; related versions can use different timing.
- For prosthetics, soft silicone, and special effects, pay particular attention to accurate mixing, mold material, mass and room temperature.
- At 73°F (23°C).
How to check readiness
Check the casting itself for flex or tack before demolding. The technical bulletin gives a pot life of 30 minutes. Flex the mold away at one edge and stop if the casting bends, tears or remains tacky.
Avoid this mistake
Demold time is not necessarily full mechanical cure.
Compare with similar products
- Compare with Alumilite Amazing Clear Cast PlusDemold: 1 day to 2 days there, 4 h here.
- Compare with EcoPoxy FlowCastDemold: 3 days there, 4 h here.
Questions
How long before you can demold this product?
Smooth-On states: The technical bulletin gives a pot life of 30 minutes. Conditions: At 73°F (23°C).. The technical bulletin gives a cure time of 4 hours. Conditions: At 73°F (23°C).. These are the manufacturer’s stated times, not a guarantee.
How does Ecoflex 00-20 compare with other maker & casting resin products?
Smooth-On states 4 hours for demold, which is quicker than the typical maker & casting resin product here (median 5 hours across 95 products). The quickest listed is Smooth-On Mold Star 14T at 9 minutes; the slowest is Smooth-On Crystal Clear 204 at 2 days.
Is there a faster Smooth-On maker & casting resin option?
Yes. Among the 94 Smooth-On maker & casting resin products listed here, Smooth-On Mold Star 14T states a shorter demold time (9 minutes versus 4 hours).
What conditions do the stated times for Ecoflex 00-20 assume?
Stated conditions: At 73°F (23°C). Baseline temperature: 73°F. Cooler, damper or thicker applications usually take longer.
How long do I have to work with this product?
Smooth-On states: The technical bulletin gives a pot life of 30 minutes. Conditions: At 73°F (23°C).. These are the manufacturer’s stated times, not a guarantee.
What affects how long this product takes to dry or cure?
Pot life and cure time shorten in warm rooms and with bigger batches. Follow the current technical bulletin for mix ratio, mixing and release agents. Follow the product label for your conditions.