Walk-on
Waterborne floor paint · NZ · manufacturer-sourced
How long before you can recoat Resene Walk-on?
Short answer
Return-to-use gates
Walk, furniture and full traffic open at different times
- Apply the Waterborne floor paint to a clean, dry subfloor
- Stay off until the foot-traffic time
- Bring in furniture and heavy use later
This product’s stated stages Quoted at 73°F
- Fully dry1–2 hours
- Ready for another coat2 hours
- Light foot traffic12 hours
- Full cure2 days
Worth noticing: You can recoat at 2 hours, but the film is not fully cured until 2 days.
Common mistake: Moving furniture back the day after, while the surface is still soft.
Return-to-use gates
Open the surface gradually instead of treating cure as one moment
Time returning to use
Your countdown
Stated times
- Ready for another coat2 hours
- Light foot traffic12 hours
- Fully dry1–2 hours
- Full cure2 days
From Resene data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.
Manufacturer website: resene.co.nz
Conditions & fine print
- Stated conditions: 73°F (23°C)
- Floor times assume the stated temperature and humidity. Cold slabs, thick coats and damp subfloors lengthen them. Follow the current data sheet.
- Region NZ. Formulas can differ between countries; check your container.
- Ready for another coat: The source gives no conditions for this time.
- Light foot traffic: The source gives no conditions for this time.
- Fully dry: The source gives no conditions for this time.
- Full cure: Maintenance such as washing waits 4 weeks.
- Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
- Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.
Confirm this is your product
Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.
- Exact listing
- Resene Walk-on
- Variant
- Waterborne floor paint
- Region
- NZ
- Listed use
- concrete floors, garage floors
- Timed stages recorded
- recoat min, light foot, full dry, full cure
- Source checked
- 2026-10-25
Documentation: Technical data sheet · Product label LL1880201, 5/24
Condition attached to the stated time: The source gives no conditions for this time.
About this product
A floor paint where the label counts hours and weeks: foot traffic at 12 hours, full cure at 48 hours, and a 4 week wait before washing. New concrete needs 28 days first.
Using this specific product
Resene Walk-on is listed here as the Waterborne floor paint version for concrete floors and garage floors. For installing or finishing a floor, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.
Before you start
- Confirm the package says Waterborne floor paint; related versions can use different timing.
- For concrete floors and garage floors, pay particular attention to subfloor condition, trowel coverage, room temperature and traffic plan.
- The source gives no conditions for this time. Maintenance such as washing waits 4 weeks.
How to check readiness
Test the least-ventilated area before walking, covering or replacing furniture. Before recoating, confirm the first coat matches the manufacturer’s stated condition; if the maximum window passed, check whether sanding is required. Try a protected edge first and avoid turning, dragging or concentrated loads. The label gives a minimum dry time of 1 to 2 hours.
Avoid this mistake
Foot traffic, furniture and rugs can have different return times.
Compare with similar products
- Compare with ArmorPoly 80Recoat: 2 h there, 2 h here.
- Compare with Bona ClassicSealRecoat: 2–3 h there, 2 h here.
Questions
How long before you can recoat this product?
Resene states: The label gives a recoat in 2 hours. Conditions: The source gives no conditions for this time.. The label gives light foot traffic 12 hours after the final coat. Conditions: The source gives no conditions for this time.. The label gives a minimum dry time of 1 to 2 hours. Conditions: The source gives no conditions for this time.. The label gives full cure in 48 hours. Conditions: Maintenance such as washing waits 4 weeks.. These are the manufacturer’s stated times, not a guarantee.
How long should new concrete wait before Resene Walk-on?
The label gives 28 days.
How long does this product take to fully cure?
Resene states: The label gives full cure in 48 hours. Conditions: Maintenance such as washing waits 4 weeks.. These are the manufacturer’s stated times, not a guarantee.
How long before I can walk on tile set with this product?
Resene states: The label gives light foot traffic 12 hours after the final coat. Conditions: The source gives no conditions for this time.. These are the manufacturer’s stated times, not a guarantee.
How long until this product is fully dry?
Resene states: The label gives a minimum dry time of 1 to 2 hours. Conditions: The source gives no conditions for this time.. These are the manufacturer’s stated times, not a guarantee.
What affects how long this product takes to dry or cure?
Floor times assume the stated temperature and humidity. Cold slabs, thick coats and damp subfloors lengthen them. Follow the current data sheet. Follow the product label for your conditions.