Nippon Paint

EA4 Finish

Two-pack epoxy finish (Malaysia) · INTL · manufacturer-sourced

Check your container: This countdown is for the Two-pack epoxy finish (Malaysia) variant. Similar-looking versions may have different times.

How long before you can recoat Nippon Paint EA4 Finish?

Short answer

Ready for another coat: 16 hours after application.
Safe to touch: 2–3 hours after application.
Industrial protective coatings

Film-build schedule

Recoat has a floor and a ceiling, and film thickness moves both

  1. Prepare the surface and apply the Two-pack epoxy finish (Malaysia) to the stated thickness
  2. Recoat inside the window the data sheet gives
  3. Return to service only at the stated cure

This product’s stated stages Quoted at 82°F

  • Safe to touch2–3 hours
  • Ready for another coat16 hours
  • Fully dry16 hours
  • Recoat window closes6 days

Worth noticing: Recoat inside the window: not before 16 hours and not after 6 days.

Common mistake: Recoating after the maximum window has closed; the next coat may not bond without abrading.

Check the recoat window

When did this coat go on?
Conditions that affect drying
Where?
Thickness

Stated times

  • Safe to touch2–3 hours
  • Recoat window closes6 days
  • Ready for another coat16 hours
  • Fully dry16 hours

From Nippon Paint data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.

Manufacturer website: nipponpaint.com.my

Conditions & fine print
  • Stated conditions: 82°F (28°C)
  • Protective-coating times are for the stated film thickness, temperature and humidity. Cold steel, thick films and poor airflow lengthen them. Follow the current data sheet.
  • Apply at 45°F or above
  • Region INTL. Formulas can differ between countries; check your container.
  • Safe to touch: At 25 to 30°C.
  • Recoat window closes: After that, dry sand the surface.
  • Ready for another coat: At 25 to 30°C.
  • Fully dry: At 25 to 30°C.
  • Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
  • Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.

Confirm this is your product

Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.

Exact listing
Nippon Paint EA4 Finish
Variant
Two-pack epoxy finish (Malaysia)
Region
INTL
Listed use
steel finish, pipework, equipment
Timed stages recorded
touch, recoat max, recoat min, full dry
Source checked
2026-10-25

Documentation: Technical data sheet · Data sheet

Condition attached to the stated time: At 25 to 30°C.

About this product

An epoxy finish that dries more slowly than the EA9: hard dry in 16 hours, with a pot life of 6 to 8 hours.

Using this specific product

Nippon Paint EA4 Finish is listed here as the Two-pack epoxy finish (Malaysia) version for steel finish, pipework, and equipment. For coating steel or industrial surfaces, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.

Before you start

  • Confirm the package says Two-pack epoxy finish (Malaysia); related versions can use different timing.
  • For steel finish, pipework, and equipment, pay particular attention to surface preparation, film thickness, temperature, dew point and pot life.
  • At 25 to 30°C. After that, dry sand the surface.

How to check readiness

Check dry film thickness and the recoat window before the next coat. Touch only a hidden edge first; a dry surface can conceal a soft layer underneath. The sheet says to recoat within 6 to 7 days. Before recoating, confirm the first coat matches the manufacturer’s stated condition; if the maximum window passed, check whether sanding is required.

Avoid this mistake

Recoat windows can close; past the maximum, abrading is usually required.

Compare with similar products

Keep going

Questions

How long before you can recoat this product?

Nippon Paint states: The sheet gives touch dry in 2 to 3 hours. Conditions: At 25 to 30°C.. The sheet says to recoat within 6 to 7 days. Conditions: After that, dry sand the surface.. The sheet gives a minimum recoat of 16 hours. Conditions: At 25 to 30°C.. The sheet gives hard dry in about 16 hours. Conditions: At 25 to 30°C.. These are the manufacturer’s stated times, not a guarantee.

How long does Nippon EA4 Finish take to hard dry?

The sheet gives about 16 hours at 25 to 30°C.

How long until this product is safe to touch?

Nippon Paint states: The sheet gives touch dry in 2 to 3 hours. Conditions: At 25 to 30°C.. These are the manufacturer’s stated times, not a guarantee.

How long until this product is fully dry?

Nippon Paint states: The sheet gives hard dry in about 16 hours. Conditions: At 25 to 30°C.. These are the manufacturer’s stated times, not a guarantee.

What affects how long this product takes to dry or cure?

Protective-coating times are for the stated film thickness, temperature and humidity. Cold steel, thick films and poor airflow lengthen them. Follow the current data sheet. Follow the product label for your conditions.

Similar products

All industrial protective coatings