Sigma Coatings

Sigmacover 295

Polyamide epoxy primer · INTL · manufacturer-sourced

Check your container: This countdown is for the Polyamide epoxy primer variant. Similar-looking versions may have different times.

How long before you can recoat Sigma Coatings Sigmacover 295?

Short answer

Ready for another coat: 8 hours after application.
Safe to touch: 2 hours after application.
Industrial protective coatings

Film-build schedule

Recoat has a floor and a ceiling, and film thickness moves both

  1. Prepare the surface and apply the Polyamide epoxy primer to the stated thickness
  2. Recoat inside the window the data sheet gives
  3. Return to service only at the stated cure

This product’s stated stages Quoted at 68°F

  • Safe to touch2 hours
  • Safe to handle3 hours
  • Ready for another coat8 hours
  • Full cure7 days

Worth noticing: Touch-dry comes at 2 hours, but full cure is 7 days, about 84 times longer.

Common mistake: Recoating after the maximum window has closed; the next coat may not bond without abrading.

Check the recoat window

When did this coat go on?
Conditions that affect drying
Where?
Thickness

Stated times

  • Safe to touch2 hours
  • Safe to handle3 hours
  • Ready for another coat8 hours
  • Full cure7 days

From Sigma Coatings data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.

Manufacturer website: None

Conditions & fine print
  • Stated conditions: 68°F (20°C)
  • Protective-coating times are for the stated film thickness, temperature and humidity. Cold steel, thick films and poor airflow lengthen them. Follow the current data sheet.
  • Apply at 23°F or above
  • Region INTL. Formulas can differ between countries; check your container.
  • Safe to touch: At 20°C substrate, up to 150 microns dry.
  • Safe to handle: At 20°C substrate, up to 150 microns dry.
  • Ready for another coat: At 20°C. The maximum is unlimited.
  • Full cure: At 20°C, up to 150 microns dry.
  • Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
  • Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.

Confirm this is your product

Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.

Exact listing
Sigma Coatings Sigmacover 295
Variant
Polyamide epoxy primer
Region
INTL
Listed use
steel primer, structural steel, marine
Timed stages recorded
touch, handle, recoat min, full cure
Source checked
2026-10-25

Documentation: Technical data sheet · Technical data sheet ref. 7947

Condition attached to the stated time: At 20°C substrate, up to 150 microns dry.

About this product

A polyamide epoxy primer with an unlimited overcoat window for epoxies but a 10 day limit for polyurethane topcoats at 20°C. Pot life is 12 hours at 20°C.

Using this specific product

Sigma Coatings Sigmacover 295 is listed here as the Polyamide epoxy primer version for steel primer, structural steel, and marine. For coating steel or industrial surfaces, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.

Before you start

  • Confirm the package says Polyamide epoxy primer; related versions can use different timing.
  • For steel primer, structural steel, and marine, pay particular attention to surface preparation, film thickness, temperature, dew point and pot life.
  • At 20°C substrate, up to 150 microns dry. At 20°C. The maximum is unlimited. At 20°C, up to 150 microns dry.

How to check readiness

Check dry film thickness and the recoat window before the next coat. Touch only a hidden edge first; a dry surface can conceal a soft layer underneath. Lift or move the item gently and avoid twisting the bond or pressing finished faces together. Before recoating, confirm the first coat matches the manufacturer’s stated condition; if the maximum window passed, check whether sanding is required.

Avoid this mistake

Recoat windows can close; past the maximum, abrading is usually required.

Compare with similar products

Keep going

Questions

How long before you can recoat this product?

Sigma Coatings states: The sheet gives dry to touch in 2 hours. Conditions: At 20°C substrate, up to 150 microns dry.. The sheet gives dry to handle in 3 hours. Conditions: At 20°C substrate, up to 150 microns dry.. The sheet gives a minimum overcoating interval of 8 hours over itself or another epoxy. Conditions: At 20°C. The maximum is unlimited.. The sheet gives full cure in 7 days. Conditions: At 20°C, up to 150 microns dry.. These are the manufacturer’s stated times, not a guarantee.

What is the polyurethane overcoat window for Sigmacover 295?

The sheet gives 16 hours to 10 days at 20°C.

How long does this product take to fully cure?

Sigma Coatings states: The sheet gives full cure in 7 days. Conditions: At 20°C, up to 150 microns dry.. These are the manufacturer’s stated times, not a guarantee.

How long until this product is safe to touch?

Sigma Coatings states: The sheet gives dry to touch in 2 hours. Conditions: At 20°C substrate, up to 150 microns dry.. These are the manufacturer’s stated times, not a guarantee.

How long until this product is safe to handle?

Sigma Coatings states: The sheet gives dry to handle in 3 hours. Conditions: At 20°C substrate, up to 150 microns dry.. These are the manufacturer’s stated times, not a guarantee.

What affects how long this product takes to dry or cure?

Protective-coating times are for the stated film thickness, temperature and humidity. Cold steel, thick films and poor airflow lengthen them. Follow the current data sheet. Follow the product label for your conditions.

Similar products

All industrial protective coatings