Loctite (Henkel)

FREKOTE R-110

Water-based release for hot molds · US · manufacturer-sourced

Check your container: This countdown is for the Water-based release for hot molds variant. Similar-looking versions may have different times.

How long does Loctite (Henkel) FREKOTE R-110 take to cure?

Short answer

Full cure: 30 minutes after application.
Mold release agents

Release-and-cast plan

Let the release dry before the pour

  1. Apply the Water-based release for hot molds in thin coats
  2. Let it flash or dry as stated
  3. Pour or mold after the stated wait

This product’s stated stages Quoted at 140°F

  • Full cure30 minutes

Worth noticing: The manufacturer states only one timing here (full cure, 30 minutes); nothing else is inferred.

Common mistake: Pouring onto a release film that is still wet; surface defects result.

Mold release agents

Project stage ladder

Demolding, handling, finishing and final use may occur at different times

ShapeSetFinishUse

For hot molds, composites, and rubber molding, identify which stage the stated cure 30 minutes milestone actually unlocks. Earlier handling does not prove final cure.

Time the release

When did you apply the release?
Conditions that affect drying
Where?
Thickness

Stated times

  • Full cure30 minutes

From Loctite (Henkel) data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.

Manufacturer website: loctiteproducts.com

Conditions & fine print
  • Stated conditions: 140°F (60°C)
  • Release agents work best on a clean, conditioned mold. Follow the current data sheet and your mold maker's instructions.
  • Temperature range: 140°F to 392°F
  • Region US. Formulas can differ between countries; check your container.
  • Full cure: At 60°C. It is 10 minutes at 100°C and 4 minutes at 150°C.
  • Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
  • Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.

Confirm this is your product

Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.

Exact listing
Loctite (Henkel) FREKOTE R-110
Variant
Water-based release for hot molds
Region
US
Listed use
hot molds, composites, rubber molding
Timed stages recorded
full cure
Source checked
2026-10-25

Documentation: Technical data sheet · TDS January 2015

Condition attached to the stated time: At 60°C. It is 10 minutes at 100°C and 4 minutes at 150°C.

About this product

A water-based release used on hot molds. Its cure time is set by mold temperature: 30 minutes at 60°C, 10 at 100°C and 4 at 150°C. The sheet asks for 4 to 6 coats and says it is suitable for mold temperatures up to 200°C.

Using this specific product

Loctite (Henkel) FREKOTE R-110 is listed here as the Water-based release for hot molds version for hot molds, composites, and rubber molding. For conditioning a mold, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.

Before you start

  • Confirm the package says Water-based release for hot molds; related versions can use different timing.
  • For hot molds, composites, and rubber molding, pay particular attention to mold material, coat count, cure between coats and mold temperature.
  • At 60°C. It is 10 minutes at 100°C and 4 minutes at 150°C.

How to check readiness

Follow the coat-by-coat schedule and the cure time before molding. Reserve full cure for demanding use, chemicals, washing, immersion or load—not merely gentle handling.

Avoid this mistake

A new or repaired mold may need a long conditioning period before production.

Keep going

Questions

How long does this product take to cure?

Loctite (Henkel) states: The data sheet says the release is fully cured after 30 minutes on a mold at 60°C. Conditions: At 60°C. It is 10 minutes at 100°C and 4 minutes at 150°C.. These are the manufacturer’s stated times, not a guarantee.

Does a hotter mold cure Frekote R-110 faster?

Yes. The sheet gives 30 minutes at 60°C, 10 minutes at 100°C and 4 minutes at 150°C. It also asks for a minimum of 6 coats on molds at 120 to 200°C or on porous molds.

What affects how long this product takes to dry or cure?

Release agents work best on a clean, conditioned mold. Follow the current data sheet and your mold maker's instructions. Follow the product label for your conditions.

Similar products

All mold release agents