COMPARISON
Paints compared by full-cure time
64 products in our catalog state a time for full cure, from 20 minutes (3M 3M Bondo 234D Ultimate Easy Sanding Body Filler) to 30 days (Tikkurila Tixomatt). The median is 7 days. The table shows the 25 shortest, built only from numeric times in manufacturer documents.
Fair-comparison rule: Read the exact milestone and conditions on each product page. Similar numbers can describe different tests, substrates or stages, and a faster time is not automatically a better product.
Comparison table
| Product | Manufacturer-stated minimum | Condition/source |
|---|---|---|
| 3M 3M Bondo 234D Ultimate Easy Sanding Body Filler Two-part body filler, CEEMEA data sheet | 20 minutes | At 25°C (77°F) with 2% hardener. |
| 3M 3M Platinum Lightweight Body Filler Two-part lightweight body filler | 20 minutes | At 77°F (25°C). |
| Bondo (3M) Bondo Fiberglass Resin Liquid resin with hardener | 2 hours | 75°F (24°C) |
| Henry 887 Tropi-Cool 100% Silicone Roof Coating White | 2 hours | Lower temperatures and/or less humidity typically slow cure. |
| Zinsser (Rust-Oleum) Zinsser Bulls Eye Zero Zero-VOC water-based primer, Canadian sheet | 2 days | At 21 to 27°C (70 to 80°F) and 50% relative humidity. |
| Corotech V515 Aliphatic Acrylic Urethane White | 3 days | At manufacturer-stated conditions; temperature, humidity and film thickness can change drying time. |
| Corotech V515 Aliphatic Acrylic Urethane Black | 3 days | At manufacturer-stated conditions; temperature, humidity and film thickness can change drying time. |
| Corotech V515 Aliphatic Acrylic Urethane Tint base | 3 days | At manufacturer-stated conditions; temperature, humidity and film thickness can change drying time. |
| Corotech V515 Aliphatic Acrylic Urethane Clear | 3 days | At manufacturer-stated conditions; temperature, humidity and film thickness can change drying time. |
| DAP Plaster Wall Patch (Dry Mix) Powder | 3 days | See product page |
| DAP Presto Patch Multi-Purpose Patching (Dry Mix) Powder | 3 days | See product page |
| INSL-X (Benjamin Moore) Stix Waterborne Bonding Primer (SXA-110) White / tintable | 3 days | Maximum scrape resistance |
| Little Greene Intelligent Matt Emulsion Washable matt emulsion (UK) | 3 days | Depends on film thickness and ambient conditions. |
| Little Greene Intelligent Satin Water-based satin for trim (UK) | 3 days | Depends on film thickness and site drying conditions. |
| Red Devil ONETIME Lightweight Spackling White | 3 days | See product page |
| Resene Lusta-Glo Enamel Solvent-borne gloss enamel (D33) | 3 days | The sheet gives no exact figure; 3 days is shown as a floor. |
| Rust-Oleum Rust-Oleum Specialty Tub & Tile Aerosol Epoxy aerosol refinish, Canadian sheet | 3 days | At 21°C (70°F). |
| Rust-Oleum Specialty Dry Erase Kit White | 3 days | At manufacturer-stated conditions; temperature, humidity and film thickness can change drying time. |
| Rust-Oleum Tub & Tile Refinishing Kit Gloss white | 3 days | 70–80°F (21–27°C) and 50% relative humidity |
| Ames Blue Max Original Liquid Rubber Waterproofer Brush-on waterproofer | 7 days | The source gives no conditions for this time. |
| Ames Maximum-Stretch Elastomeric waterproof coating | 7 days | The source gives no conditions for this time. |
| BEHR BEHR DYNASTY Interior Paint All sheens and colors | 7 days | Before washing the paint |
| Haymes Elite Rapid Cote High Gloss Quick-drying gloss (Australia) | 7 days | Avoid steam for 72 hours. |
| INSL-X Epoxy Pool Coating White | 7 days | At manufacturer-stated conditions; temperature, humidity and film thickness can change drying time. |
| INSL-X Epoxy Pool Coating Ocean blue | 7 days | At manufacturer-stated conditions; temperature, humidity and film thickness can change drying time. |
Quick answers
Which has the shortest stated time for full cure?
Among the 64 products in our catalog with a numeric milestone for full cure, the shortest is 3M 3M Bondo 234D Ultimate Easy Sanding Body Filler at 20 minutes.
How wide is the range for full cure?
Stated times run from 20 minutes to 30 days, with a median of 7 days across 26 manufacturers.
What can change the order?
Temperature, humidity, thickness, airflow, surface preparation and what the manufacturer means by this milestone can all change which product is right. We keep the manufacturer wording on each product page so you can check before relying on a number.