Magna Durable Grey
Durable resin for LCD printers · US · manufacturer-sourced
How long should Siraya Tech Magna Durable Grey be left to cure?
Short answer
Cast-and-demold plan
Gel, demold and full cure are separate days
- Mix the Durable resin for LCD printers to ratio and pour
- Wait for the demold time
- Sand or finish after full cure
This product’s stated stages Quoted at 73°F
- Curing period10–15 minutes
Worth noticing: The manufacturer states only one timing here (curing period, 10–15 minutes); nothing else is inferred.
Common mistake: Demolding early and leaving a soft, tacky casting that never fully hardens.
Project stage ladder
Demolding, handling, finishing and final use may occur at different times
For 3D printing and durable parts, identify which stage the stated period 10–15 minutes milestone actually unlocks. Earlier handling does not prove final cure.
Time demold and cure
Your countdown
Stated times
- Curing period complete10–15 minutes
From Siraya Tech data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.
Manufacturer website: siraya.tech
Conditions & fine print
- Stated conditions: 73°F (23°C)
- UV post-cure depends on lamp output and part shape. Follow the current data sheet.
- Region US. Formulas can differ between countries; check your container.
- Curing period complete: The source gives no conditions for this time.
- Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
- Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.
Confirm this is your product
Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.
- Exact listing
- Siraya Tech Magna Durable Grey
- Variant
- Durable resin for LCD printers
- Region
- US
- Listed use
- 3D printing, durable parts
- Timed stages recorded
- cure period
- Source checked
- 2026-10-25
Documentation: Technical data sheet · TDS page, undated; copyright 2026
Condition attached to the stated time: The source gives no conditions for this time.
About this product
A durable grey resin cured for 10 to 15 minutes with the part rotated every 5 minutes. The only temperatures on the page are for warming the resin, 40 to 60°C, and printing, 25 to 30°C, not post-cure.
Using this specific product
Siraya Tech Magna Durable Grey is listed here as the Durable resin for LCD printers version for 3D printing and durable parts. For casting resin, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.
Before you start
- Confirm the package says Durable resin for LCD printers; related versions can use different timing.
- For 3D printing and durable parts, pay particular attention to accurate mixing, mold material, mass and room temperature.
- The source gives no conditions for this time.
How to check readiness
Check the casting itself for flex or tack before demolding. The data sheet says to cure with 395 to 405 nm UV light for about 10 to 15 minutes.
Avoid this mistake
Demold time is not necessarily full mechanical cure.
Questions
How long should this product be left to cure?
Siraya Tech states: The data sheet says to cure with 395 to 405 nm UV light for about 10 to 15 minutes. Conditions: The source gives no conditions for this time.. These are the manufacturer’s stated times, not a guarantee.
Does the Magna Durable page give a post-cure temperature?
No. It gives 10 to 15 minutes under 395 to 405 nm UV. The temperatures it lists are for warming the resin to 40 to 60°C and printing at 25 to 30°C.
What affects how long this product takes to dry or cure?
UV post-cure depends on lamp output and part shape. Follow the current data sheet. Follow the product label for your conditions.