Multi-Surface All-Purpose Water Repellent
Clear water repellent · US · manufacturer-sourced
How long before you can recoat Seal-Krete Multi-Surface All-Purpose Water Repellent?
Short answer
Paver-joint plan
Brush in, wet down, then wait before traffic
- Sweep the Clear water repellent into dry joints
- Activate as the label directs
- Keep traffic off until the stated time
This product’s stated stages Quoted at 77°F and 50% humidity
- Safe to touch1 hour
- Ready for another coat2 hours
- Light foot traffic1 day
- Heavy traffic3 days
Worth noticing: Safe to touch at 1 hour; heavy traffic at 3 days.
Common mistake: Letting rain or sprinklers hit joints that have not hardened.
Return-to-use gates
Open the surface gradually instead of treating cure as one moment
Time the paver cure
Your countdown
Stated times
- Safe to touch1 hour
- Ready for another coat2 hours
- Light foot traffic1 day
- Heavy traffic3 days
From Seal-Krete data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.
Manufacturer website: seal-krete.com
Conditions & fine print
- Stated conditions: 77°F (25°C) and 50% relative humidity
- Times depend on temperature, humidity, film thickness and sunshine. Follow the current label for your surface and weather. The ASTM D-1640 table in the same sheet lists different numbers (touch 15 minutes, recoat 4 hours), so use the dry-time section for field planning. Do not apply if the temperature will drop below 50°F within 24 hours.
- Temperature range: 50°F to 90°F
- Region US. Formulas can differ between countries; check your container.
- Safe to touch: At 77°F (25°C) and 50% relative humidity.
- Ready for another coat: At 77°F (25°C) and 50% relative humidity.
- Light foot traffic: At 77°F (25°C) and 50% relative humidity.
- Heavy traffic: At 77°F (25°C) and 50% relative humidity.
- Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
- Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.
Confirm this is your product
Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.
- Exact listing
- Seal-Krete Multi-Surface All-Purpose Water Repellent
- Variant
- Clear water repellent
- Region
- US
- Listed use
- concrete sealer, masonry, water repellent
- Timed stages recorded
- touch, recoat min, light foot, heavy traffic
- Source checked
- 2026-10-25
Documentation: Technical data sheet · 64049-082117-SK
Condition attached to the stated time: At 77°F (25°C) and 50% relative humidity.
About this product
A clear, water-based repellent for concrete, brick and other masonry. The sheet carries two sets of dry times: a field set (touch 1 hour, recoat 2 hours) and a laboratory ASTM set (touch 15 minutes, recoat 4 hours).
Using this specific product
Seal-Krete Multi-Surface All-Purpose Water Repellent is listed here as the Clear water repellent version for concrete sealer, masonry, and water repellent. For using this product, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.
Before you start
- Confirm the package says Clear water repellent; related versions can use different timing.
- For concrete sealer, masonry, and water repellent, pay particular attention to the exact variant, preparation and environmental conditions.
- At 77°F (25°C) and 50% relative humidity.
How to check readiness
Check the real material or treated area at the slowest location before the next step. Touch only a hidden edge first; a dry surface can conceal a soft layer underneath. Before recoating, confirm the first coat matches the manufacturer’s stated condition; if the maximum window passed, check whether sanding is required. Try a protected edge first and avoid turning, dragging or concentrated loads.
Avoid this mistake
The first visible change is not always the manufacturer’s final-use milestone.
Compare with similar products
- Compare with Black Jack (Gardner-Gibson) Drive-Maxx 1000 Premium Filler & SealerRecoat: 3–6 h there, 2 h here.
- Compare with Black Jack (Gardner-Gibson) CAS-73 Commercial Asphalt SealerRecoat: 2–4 h there, 2 h here.
Questions
How long before you can recoat this product?
Seal-Krete states: The data sheet gives 1 hour to dry to the touch. Conditions: At 77°F (25°C) and 50% relative humidity.. The data sheet gives 2 hours to recoat. Conditions: At 77°F (25°C) and 50% relative humidity.. The data sheet allows foot traffic in 24 hours. Conditions: At 77°F (25°C) and 50% relative humidity.. The data sheet allows vehicular traffic in 72 hours. Conditions: At 77°F (25°C) and 50% relative humidity.. These are the manufacturer’s stated times, not a guarantee.
Which of the two recoat times on the Seal-Krete sheet should I follow?
The data sheet's Dry Time section says recoat in 2 hours at 77°F and 50% humidity. The ASTM D-1640 table later in the same sheet says 4 hours. For a driveway or wall, the longer 4 hour figure is the safer wait if conditions are cooler or more humid than 77°F and 50%.
How long before I can walk on tile set with this product?
Seal-Krete states: The data sheet allows foot traffic in 24 hours. Conditions: At 77°F (25°C) and 50% relative humidity.. These are the manufacturer’s stated times, not a guarantee.
How long before heavy traffic is safe on this product?
Seal-Krete states: The data sheet allows vehicular traffic in 72 hours. Conditions: At 77°F (25°C) and 50% relative humidity.. These are the manufacturer’s stated times, not a guarantee.
How long until this product is safe to touch?
Seal-Krete states: The data sheet gives 1 hour to dry to the touch. Conditions: At 77°F (25°C) and 50% relative humidity.. These are the manufacturer’s stated times, not a guarantee.
What affects how long this product takes to dry or cure?
Times depend on temperature, humidity, film thickness and sunshine. Follow the current label for your surface and weather. The ASTM D-1640 table in the same sheet lists different numbers (touch 15 minutes, recoat 4 hours), so use the dry-time section for field planning. Do not apply if the temperature will drop below 50°F within 24 hours. Follow the product label for your conditions.