International (AkzoNobel)

Interzinc 2265

Zinc epoxy primer · INTL · manufacturer-sourced

Check your container: This countdown is for the Zinc epoxy primer variant. Similar-looking versions may have different times.

How long before you can recoat International (AkzoNobel) Interzinc 2265?

Short answer

Ready for another coat: 9 hours after application.
Safe to touch: 20 minutes after application.

Confirm this is your product

Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.

Exact listing
International (AkzoNobel) Interzinc 2265
Variant
Zinc epoxy primer
Region
INTL
Listed use
zinc epoxy primer, steel
Timed stages recorded
touch, recoat min, full dry
Source checked
2026-10-25

Documentation: Technical data sheet · Product data sheet, 05/02/2015

Condition attached to the stated time: It is 30 minutes at 5°C and 5 minutes at 40°C.

About this product

A zinc primer with a very fast dry, 20 minutes to touch, but an overcoat minimum of 9 hours at 15°C, so most of the wait is chemical cure, not drying.

Industrial protective coatings

Film-build schedule

Recoat has a floor and a ceiling, and film thickness moves both

  1. Prepare the surface and apply the Zinc epoxy primer to the stated thickness
  2. Recoat inside the window the data sheet gives
  3. Return to service only at the stated cure

This product’s stated stages Quoted at 59°F

  • Safe to touch20 minutes
  • Fully dry1 hour 30 min
  • Ready for another coat9 hours

Worth noticing: Safe to touch at 20 minutes; ready for another coat at 9 hours.

Common mistake: Recoating after the maximum window has closed; the next coat may not bond without abrading.

Industrial protective coatings

Coat timeline

Plan the next coat and final use separately

  1. 1
    ApplyUse the Zinc epoxy primer directions and prepare for zinc epoxy primer and steel.
  2. 2
    Next coatUse the listed recoat milestone; do not substitute touch-dry time.
  3. 3
    Normal useWait for the applicable handling, water or cure milestone.

Check the recoat window

When did this coat go on?
Conditions that affect drying
Where?
Thickness

Stated times

  • Safe to touch20 minutes
  • Ready for another coat9 hours
  • Fully dry90 minutes

From International (AkzoNobel) data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.

Manufacturer website: international-yachtpaint.com

Conditions & fine print
  • Stated conditions: 59°F (15°C)
  • Protective-coating times are for the stated film thickness, temperature and humidity. Cold steel, thick films and poor airflow lengthen them. Follow the current data sheet.
  • Region INTL. Formulas can differ between countries; check your container.
  • Safe to touch: It is 30 minutes at 5°C and 5 minutes at 40°C.
  • Ready for another coat: It is 18 hours at 5°C and 90 minutes at 40°C.
  • Fully dry: It is 3 hours at 5°C and 30 minutes at 40°C.
  • Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
  • Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.

Using this specific product

International (AkzoNobel) Interzinc 2265 is listed here as the Zinc epoxy primer version for zinc epoxy primer and steel. For coating steel or industrial surfaces, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.

Before you start

  • Confirm the package says Zinc epoxy primer; related versions can use different timing.
  • For zinc epoxy primer and steel, pay particular attention to surface preparation, film thickness, temperature, dew point and pot life.
  • It is 30 minutes at 5°C and 5 minutes at 40°C. It is 18 hours at 5°C and 90 minutes at 40°C. It is 3 hours at 5°C and 30 minutes at 40°C.

How to check readiness

Check dry film thickness and the recoat window before the next coat. Touch only a hidden edge first; a dry surface can conceal a soft layer underneath. Before recoating, confirm the first coat matches the manufacturer’s stated condition; if the maximum window passed, check whether sanding is required. The sheet gives hard dry at 90 minutes at 15°C.

Avoid this mistake

Recoat windows can close; past the maximum, abrading is usually required.

Compare with similar products

Keep going

Questions

How long before you can recoat this product?

International (AkzoNobel) states: The sheet gives touch dry at 20 minutes at 15°C. Conditions: It is 30 minutes at 5°C and 5 minutes at 40°C.. The sheet gives a minimum overcoat interval of 9 hours at 15°C. Conditions: It is 18 hours at 5°C and 90 minutes at 40°C.. The sheet gives hard dry at 90 minutes at 15°C. Conditions: It is 3 hours at 5°C and 30 minutes at 40°C.. These are the manufacturer’s stated times, not a guarantee.

Why is the Interzinc 2265 overcoat time so much longer than its dry time?

The sheet gives hard dry at 90 minutes but a minimum overcoat of 9 hours at 15°C.

How long until this product is safe to touch?

International (AkzoNobel) states: The sheet gives touch dry at 20 minutes at 15°C. Conditions: It is 30 minutes at 5°C and 5 minutes at 40°C.. These are the manufacturer’s stated times, not a guarantee.

How long until this product is fully dry?

International (AkzoNobel) states: The sheet gives hard dry at 90 minutes at 15°C. Conditions: It is 3 hours at 5°C and 30 minutes at 40°C.. These are the manufacturer’s stated times, not a guarantee.

What affects how long this product takes to dry or cure?

Protective-coating times are for the stated film thickness, temperature and humidity. Cold steel, thick films and poor airflow lengthen them. Follow the current data sheet. Follow the product label for your conditions.

Similar products

All industrial protective coatings