WEST SYSTEM

WEST SYSTEM 105/207 Special Clear Hardener

Epoxy resin with 207 Special Clear Hardener · US · manufacturer-sourced

Check your container: This countdown is for the Epoxy resin with 207 Special Clear Hardener variant. Similar-looking versions may have different times.

How long does WEST SYSTEM 105/207 Special Clear Hardener take to dry?

Short answer

Set / hardened: 10–15 hours after application.
Epoxy

Two-part cure ladder

Pot life, set and full cure all run off the mix time

  1. Mix the Epoxy resin with 207 Special Clear Hardener in the exact ratio
  2. Work inside the pot life
  3. Do not load until the stated cure

This product’s stated stages Quoted at 72°F

  • Working time ends22–26 minutes
  • Set10–15 hours
  • Ready for load1–4 days

Worth noticing: Working time is only 22–26 minutes; the next stated stage, set, is 10–15 hours.

Common mistake: Mixing a large batch in a warm room; the pot life is shorter than the sheet suggests.

Epoxy

Bond-strength path

Assembly, handling and full load are different stages

1 · AssembleClean, fit and apply the Epoxy resin with 207 Special Clear Hardener version correctly.
2 · HoldKeep the joint undisturbed through its set or clamp stage.
3 · LoadUse full cure—not surface firmness—before demanding use.

Time the epoxy cure

When did you mix the epoxy?
Conditions that affect drying
Where?
Thickness

Stated times

  • Working time ends22–26 minutes
  • Set / hardened10–15 hours
  • Can take load or strain1–4 days

From WEST SYSTEM data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.

Manufacturer website: westsystem.com

Conditions & fine print
  • Stated conditions: 72°F (22°C)
  • Pot life and cure time shorten in heat, with larger mixed batches and in thick sections. Follow the current data sheet for mixing, surface preparation and loading. The data sheet gives a thin-film working time of 110 minutes to 2 hours and a minimum recommended temperature of 60°F.
  • Apply at 60°F or above
  • Region US. Formulas can differ between countries; check your container.
  • Working time ends: At 72°F (22°C).
  • Set / hardened: At 72°F (22°C).
  • Can take load or strain: At 72°F (22°C).
  • Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
  • Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.

Confirm this is your product

Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.

Exact listing
WEST SYSTEM WEST SYSTEM 105/207 Special Clear Hardener
Variant
Epoxy resin with 207 Special Clear Hardener
Region
US
Listed use
boat building, epoxy repair, wood bonding
Timed stages recorded
tooling, set, load ready
Source checked
2026-10-25

Documentation: Technical data sheet · October 2014

Condition attached to the stated time: At 72°F (22°C).

About this product

WEST SYSTEM 105/207 Special Clear Hardener is an epoxy product from WEST SYSTEM, listed for boat building, epoxy repair, wood bonding. The source gives a range for set: 10–15 hours. This page tracks 3 stated steps, from working time at 22 minutes to load at 1 day.

Using this specific product

WEST SYSTEM WEST SYSTEM 105/207 Special Clear Hardener is listed here as the Epoxy resin with 207 Special Clear Hardener version for boat building, epoxy repair, and wood bonding. For mixing and curing epoxy, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.

Before you start

  • Confirm the package says Epoxy resin with 207 Special Clear Hardener; related versions can use different timing.
  • For boat building, epoxy repair, and wood bonding, pay particular attention to mix ratio, batch size, temperature and pour thickness.
  • At 72°F (22°C).

How to check readiness

Check the coolest or thickest part for firmness before sanding, demolding or loading. The data sheet gives a pot life of 22 minutes to 26 minutes for 100 grams. The data sheet gives 10 to 15 hours to cure to a solid in a thin film. The data sheet gives 1 to 4 days to cure to working strength.

Avoid this mistake

A larger batch can heat faster while a thin film may cure more slowly.

Compare with similar products

Keep going

Questions

How long does this product take to dry?

WEST SYSTEM states: The data sheet gives a pot life of 22 minutes to 26 minutes for 100 grams. Conditions: At 72°F (22°C).. The data sheet gives 10 to 15 hours to cure to a solid in a thin film. Conditions: At 72°F (22°C).. The data sheet gives 1 to 4 days to cure to working strength. Conditions: At 72°F (22°C).. These are the manufacturer’s stated times, not a guarantee.

How does WEST SYSTEM 105/207 Special Clear Hardener compare with other epoxy products?

WEST SYSTEM states 10 hours for set, which is slower than the typical epoxy product here (median 17 minutes across 32 products). The quickest listed is J-B Weld MinuteWeld Syringe at 1 minute; the slowest is WEST SYSTEM 105/209 Extra Slow Hardener at 20 hours.

Is there a faster WEST SYSTEM epoxy option?

Yes. Among the 7 WEST SYSTEM epoxy products listed here, WEST SYSTEM G/flex 650 states a shorter set time (3 hours versus 10 hours).

What conditions do the stated times for WEST SYSTEM 105/207 Special Clear Hardener assume?

Stated conditions: At 72°F (22°C). Baseline temperature: 72°F. Application temperature: 60°F or higher. Cooler, damper or thicker applications usually take longer.

How long do I have to work with this product?

WEST SYSTEM states: The data sheet gives a pot life of 22 minutes to 26 minutes for 100 grams. Conditions: At 72°F (22°C).. These are the manufacturer’s stated times, not a guarantee.

What affects how long this product takes to dry or cure?

Pot life and cure time shorten in heat, with larger mixed batches and in thick sections. Follow the current data sheet for mixing, surface preparation and loading. The data sheet gives a thin-film working time of 110 minutes to 2 hours and a minimum recommended temperature of 60°F. Follow the product label for your conditions.

Similar products

All epoxies