QUIKRETE

Advanced Polymer Concrete Crack Sealant

Concrete crack sealant · US · not yet reviewed

Check your container: This countdown is for the Concrete crack sealant variant. Similar-looking versions may have different times.

How long before you can paint over QUIKRETE Advanced Polymer Concrete Crack Sealant?

Short answer

Paint-ready: 2 hours after application.
Full cure: 3–7 days after application.
Caulk & sealant

Bond-strength path

Assembly, handling and full load are different stages

1 · AssembleClean, fit and apply the Concrete crack sealant version correctly.
2 · HoldKeep the joint undisturbed through its set or clamp stage.
3 · LoadUse full cure—not surface firmness—before demanding use.

Calculate bond readiness

When was the bond assembled?
Conditions that affect drying
Where?
Thickness

Stated times

  • Tack-free1 hour
  • Paint-ready2 hours
  • Light foot traffic3 days
  • Full cure3–7 days

From QUIKRETE data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.

Manufacturer website: quikrete.com

Conditions & fine print
  • Stated conditions: 77°F (25°C) and 50% relative humidity
  • Low humidity, cooler temperatures and non-porous substrates lengthen cure times. Apply between 40°F and 95°F.
  • Temperature range: 40°F to 95°F
  • Region US. Formulas can differ between countries; check your container.
  • Tack-free: 77°F and 50% RH
  • Entered from the manufacturer source; second review pending. Report outdated information
  • Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.

Using this specific product

QUIKRETE Advanced Polymer Concrete Crack Sealant is listed here as the Concrete crack sealant version for concrete cracks, sidewalk, and driveway. For sealing a joint, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.

Before you start

  • Confirm the package says Concrete crack sealant; related versions can use different timing.
  • For concrete cracks, sidewalk, and driveway, pay particular attention to joint depth, tooling, ventilation and exposure to water.
  • 77°F and 50% RH.

How to check readiness

Probe an inconspicuous edge for a continuous skin and follow the stated water-exposure milestone. Tack-free time: 60 minutes. Allow the sealant to cure for a minimum of 2 hours before painting with a water-based latex paint. Try a protected edge first and avoid turning, dragging or concentrated loads.

Avoid this mistake

Surface skin is not the same as through-cure, especially in a deep joint.

Questions

How long until I can shower after using this product?

QUIKRETE does not state a shower or water-ready time for this product in its source document. The nearest stated time. QUIKRETE states: Typical full cure in 3 to 7 days. Temporary water immersion requires 7 days. These are the manufacturer’s stated times, not a guarantee. Check the container for the latest instructions.

How long does this product take to dry?

QUIKRETE states: Allow the sealant to cure for a minimum of 2 hours before painting with a water-based latex paint. Typical full cure in 3 to 7 days. Temporary water immersion requires 7 days. Cure for a minimum of 3 days before exposing to traffic. These are the manufacturer’s stated times, not a guarantee.

How long until I can paint over this product?

QUIKRETE states: Allow the sealant to cure for a minimum of 2 hours before painting with a water-based latex paint. These are the manufacturer’s stated times, not a guarantee.

How long until I can walk or drive on this product?

QUIKRETE states: Cure for a minimum of 3 days before exposing to traffic. These are the manufacturer’s stated times, not a guarantee.

How long does this product take to fully cure?

QUIKRETE states: Typical full cure in 3 to 7 days. Temporary water immersion requires 7 days. These are the manufacturer’s stated times, not a guarantee.

How long until this product is safe to touch or handle?

QUIKRETE states: Tack-free time: 60 minutes. Conditions: 77°F and 50% RH. These are the manufacturer’s stated times, not a guarantee.

What affects how long this product takes to dry or cure?

Low humidity, cooler temperatures and non-porous substrates lengthen cure times. Apply between 40°F and 95°F. Application temperature: 40°F to 95°F. Follow the product label for your conditions.

Similar products

All caulks and sealants