LATICRETE

LATICRETE LATASIL

Silicone sealant · US · manufacturer-sourced

Check your container: This countdown is for the Silicone sealant variant. Similar-looking versions may have different times.

How long does LATICRETE LATASIL take to dry?

Short answer

Tack-free: 17 minutes after application.
Caulk & sealant

Bead cure stages

Skin, tack-free and paint-ready are not the same moment

  1. Gun a continuous bead of Silicone sealant
  2. Tool it inside the working time
  3. Keep it dry until the stated water-ready time

This product’s stated stages Quoted at 73°F and 50% humidity

  • Working time ends7–10 minutes
  • Tack-free17 minutes

Worth noticing: Working time is only 7–10 minutes; the next stated stage, tack-free, is 17 minutes.

Common mistake: Showering or painting at skin-over, when the bead is only crusted on the outside.

Caulk & sealant

Bond-strength path

Assembly, handling and full load are different stages

1 · AssembleClean, fit and apply the Silicone sealant version correctly.
2 · HoldKeep the joint undisturbed through its set or clamp stage.
3 · LoadUse full cure—not surface firmness—before demanding use.

Time the caulk cure

When did you run the bead?
Conditions that affect drying
Where?
Thickness

Stated times

  • Working time ends7–10 minutes
  • Tack-free17 minutes

From LATICRETE data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.

Manufacturer website: laticrete.com

Conditions & fine print
  • Stated conditions: 73°F (23°C) and 50% relative humidity
  • Skin and cure times depend on temperature, humidity and bead depth. Follow the current data sheet.
  • Region US. Formulas can differ between countries; check your container.
  • Working time ends: The source gives no conditions for this time.
  • Tack-free: At 77°F (25°C) and 50% relative humidity.
  • Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
  • Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.

Confirm this is your product

Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.

Exact listing
LATICRETE LATICRETE LATASIL
Variant
Silicone sealant
Region
US
Listed use
tile joints, movement joints, kitchens and baths
Timed stages recorded
tooling, tack free
Source checked
2026-10-25

Documentation: Technical data sheet · TDS 132, 23 March 2026

Condition attached to the stated time: The source gives no conditions for this time.

About this product

A silicone for tile movement joints. The sheet gives a tooling time of 7 to 10 minutes and a tack-free time of 17 minutes, and pairs it with LATASIL 9118 Primer, which has its own 30 minute cure.

Using this specific product

LATICRETE LATICRETE LATASIL is listed here as the Silicone sealant version for tile joints, movement joints, and kitchens and baths. For sealing a joint, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.

Before you start

  • Confirm the package says Silicone sealant; related versions can use different timing.
  • For tile joints, movement joints, and kitchens and baths, pay particular attention to joint depth, tooling, ventilation and exposure to water.
  • The source gives no conditions for this time. At 77°F (25°C) and 50% relative humidity.

How to check readiness

Probe an inconspicuous edge for a continuous skin and follow the stated water-exposure milestone. The data sheet gives a tooling time of 7 to 10 minutes. The data sheet gives a tack-free time of 17 minutes.

Avoid this mistake

Surface skin is not the same as through-cure, especially in a deep joint.

Compare with similar products

Keep going

Questions

How long does this product take to dry?

LATICRETE states: The data sheet gives a tooling time of 7 to 10 minutes. Conditions: The source gives no conditions for this time.. The data sheet gives a tack-free time of 17 minutes. Conditions: At 77°F (25°C) and 50% relative humidity.. These are the manufacturer’s stated times, not a guarantee.

How long do I have to tool LATICRETE LATASIL?

The data sheet gives 7 to 10 minutes, with tack-free at 17 minutes at 77°F and 50% humidity.

How long do I have to work with this product?

LATICRETE states: The data sheet gives a tooling time of 7 to 10 minutes. Conditions: The source gives no conditions for this time.. These are the manufacturer’s stated times, not a guarantee.

What affects how long this product takes to dry or cure?

Skin and cure times depend on temperature, humidity and bead depth. Follow the current data sheet. Follow the product label for your conditions.

Similar products

All caulks and sealants