Dymax

Multi-Cure 1184-M-T

Medical device adhesive · US · manufacturer-sourced

Check your container: This countdown is for the Medical device adhesive variant. Similar-looking versions may have different times.

How long does Dymax Multi-Cure 1184-M-T take to dry?

Short answer

Set / hardened: 1 minute after application.
Full cure: 15 minutes to 1 hour after application.
Light-curing adhesives

Light-cure routine

The lamp sets the surface; the stated time finishes the job

  1. Apply the Medical device adhesive in thin layers
  2. Cure under the lamp for the stated time
  3. Let any post-cure finish before handling

This product’s stated stages Quoted at 23°F

  • Set1 minute
  • Full cure15 minutes to 1 hour

Worth noticing: Set at 1 minute; full cure at 15 minutes to 1 hour.

Common mistake: Curing a thick layer under a weak lamp; the surface sets while the inside stays liquid.

Light-curing adhesives

Bond-strength path

Assembly, handling and full load are different stages

1 · AssembleClean, fit and apply the Medical device adhesive version correctly.
2 · HoldKeep the joint undisturbed through its set or clamp stage.
3 · LoadUse full cure—not surface firmness—before demanding use.

Time the light cure

When did you cure it?
Conditions that affect drying
Where?
Thickness

Stated times

  • Set / hardened1 minute
  • Full cure15 minutes to 1 hour

From Dymax data sheet · checked 2026-10-25. Anything not listed isn’t stated by the manufacturer.

Manufacturer website: dymax.com

Conditions & fine print
  • Stated conditions: 23°F (-5°C)
  • Fixture and cure times assume the lamp type and intensity stated on the data sheet. Shadowed areas and thick bond lines need more exposure or a secondary cure.
  • Region US. Formulas can differ between countries; check your container.
  • Set / hardened: Fixture time is the time to reach 0.1 N/mm² (10 psi) shear strength between glass slides under the stated lamp.
  • Full cure: Heat cure comes after the light cure.
  • Entered from the cited manufacturer documentation. Check the current label for the exact formula and region. Report outdated information
  • Actual results depend on preparation, thickness, ventilation, temperature, humidity, mixing and substrate.

Confirm this is your product

Closely named formulas, colors and regional versions can use different times. Match these details to your container before starting a countdown.

Exact listing
Dymax Multi-Cure 1184-M-T
Variant
Medical device adhesive
Region
US
Listed use
medical device bonding
Timed stages recorded
set, full cure
Source checked
2026-10-25

Documentation: Technical data sheet · REV. 12/27/2018

Condition attached to the stated time: Fixture time is the time to reach 0.1 N/mm² (10 psi) shear strength between glass slides under the stated lamp.

About this product

A Dymax MD medical-device adhesive. The sheet's numbers are 1 second on the older lamps and 0.4 second on BlueWave LED lamps, with conveyor belt speeds at 8.2 m/min. Heat can serve as a secondary cure, but only after the light cure.

Using this specific product

Dymax Multi-Cure 1184-M-T is listed here as the Medical device adhesive version for medical device bonding. For curing with light, the useful question is not simply whether the surface looks finished—it is whether the exact next-action milestone shown above has been reached.

Before you start

  • Confirm the package says Medical device adhesive; related versions can use different timing.
  • For medical device bonding, pay particular attention to lamp type, irradiance, distance, bond-line thickness and shadowed areas.
  • Fixture time is the time to reach 0.1 N/mm² (10 psi) shear strength between glass slides under the stated lamp. Heat cure comes after the light cure.

How to check readiness

Confirm the joint is fixtured, then give the stated extra exposure or secondary cure for full properties. The data sheet gives the fixture time in seconds, so the page uses the one-minute minimum the calculator can show. The sheet gives a fixture time of 1 second under 2000-EC or 5000-EC lamps and 0.4 second with BlueWave LED lamps. Reserve full cure for demanding use, chemicals, washing, immersion or load—not merely gentle handling.

Avoid this mistake

Fixture time is only the first step; a full cure takes longer than the time the part stays in the light.

Keep going

Questions

How long does this product take to dry?

Dymax states: The data sheet gives the fixture time in seconds, so the page uses the one-minute minimum the calculator can show. The sheet gives a fixture time of 1 second under 2000-EC or 5000-EC lamps and 0.4 second with BlueWave LED lamps. Conditions: Fixture time is the time to reach 0.1 N/mm² (10 psi) shear strength between glass slides under the stated lamp.. The data sheet gives a heat cure of 110°C for 60 minutes, 120°C for 30 minutes or 150°C for 15 minutes where light cannot reach, after the light cure. Conditions: Heat cure comes after the light cure.. These are the manufacturer’s stated times, not a guarantee.

Can the 1184-M-T cure with heat alone?

No. The sheet gives heat as a secondary cure where light cannot reach, and light curing must come first: 110°C for 60 minutes, 120°C for 30 or 150°C for 15.

How long does this product take to fully cure?

Dymax states: The data sheet gives a heat cure of 110°C for 60 minutes, 120°C for 30 minutes or 150°C for 15 minutes where light cannot reach, after the light cure. Conditions: Heat cure comes after the light cure.. These are the manufacturer’s stated times, not a guarantee.

What affects how long this product takes to dry or cure?

Fixture and cure times assume the lamp type and intensity stated on the data sheet. Shadowed areas and thick bond lines need more exposure or a secondary cure. Follow the product label for your conditions.

Similar products

All light-curing adhesives